background image

SAFETY GUIDELINES

CARE & MAINTENANCE

Limited Warranty

Poly-Tex, Inc. warrants its products to be free from defects in material and workmanship for a
period of (1) year from date of invoice. This warranty is provided to the original purchaser of the
product and is not transferable. Poly-Tex does not warrant parts not manufactured by Poly-Tex,
but does assign any transferable manufacturer or supplier warranties. Should any defect be
found, full repair or replacement will be rendered to the customer at no cost following inspection
by a Poly-Tex representative and the return of the defective product to our Castle Rock, MN
factory. Expenses for removal or reinstallation of defective products will not be covered by the
warranty.

POLY-TEX SHALL NOT BE HELD RESPONSIBLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES, OR FOR ANY DELAY IN PERFORMANCE OF THIS
WARRANTY BEYOND OUR CONTROL. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES WHETHER IMPLIED, WRITTEN OR ORAL INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

This warranty does not cover damage from customer abuse, misuse, improper installation,
customer modifications, customer negligence in performing normal maintenance, damage
resulting from acts of nature.

Contact information

Poly-Tex, Inc. PO Box 458

27725 Danville Ave Castle Rock, MN 55010

Toll free (800) 852-3443 Fax (651) 463-2479

www.poly-tex.com

Do not

climb, sit on, or use this product as a ladder. Injuries may occur.

Do not

place or install electrical items on this product. Wet conditions are typical and

electrical shock may occur.

Do not

place this product on a slope that exceeds 3 degrees.

Do not

move this display after product is in place. Damage to display and injuries may occur.

To remove loose soil and debris, simply spray the soiled areas with water from a garden hose.

Prior to storage, all surfaces of this product should be sprayed down with water and allowed to dry
completely.

Содержание CD3550









Отзывы: