manualshive.com logo in svg

Politec Sandor Dual, Инструкция по установке и монтажу

Поделиться
Скачать
Politec Sandor Dual Скачать руководство пользователя страница 27

27

SANDOR PLUS SMA 

POLITEC | INSTALLATION MANUAL - VER.2.6

TX TEST

By setting all the DIP switches to OFF, all the transmitters in the column 
are turned off; by moving all the DIP switches to ON the transmitters are 
activated at high frequency in order to allow a first visual contact 
between the transmitter and the receiver in case of difficulty at long 
distances.

1 CH 1

Wired synchronism: normal operation of the transmitters
Optical synchronism: operation with transmission frequency 1

2 CH 2

Wired synchronism: no operation 
Optical synchronism: operation with transmission frequency 2

3 CH 3

Wired synchronism: no operation 
Optical synchronism: operation with transmission frequency 3

4 CH 4

Wired synchronism: no operation 
Optical synchronism: operation with transmission frequency 4, only 2 
transmitters are active

4 DIP SWITCH UNIT TX

TERMINAL and
TX ONLY

All DIP switches are ON: the alarm relay is deactivated.This setting is 
used when the column has only transmitter optics  

1 CH 1

Wired synchronism: normal operation of the receivers
Optical synchronism: operation with reception frequency 1

2 CH 2

Wired synchronism: no operation 
Optical synchronism: operation with reception frequency 2

3 CH 3

Wired synchronism: no operation 
Optical synchronism: operation with reception frequency 3

4 CH 4

Wired synchronism: no operation 
Optical synchronism: operation with reception frequency 4, only 2 
receivers are active

4 DIP SWITCH UNIT RX

DISQ1 JUMPER:J7

If the disqualification function has been activated on DIP SWITCH 12 via DIP 5 in ON, in some
cases and particular geographical areas, it may be useful to increase the sensitivity of the
disqualification by setting jumper J7 to ON.

Содержание Sandor Dual





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды