background image

16. FAQ

19

ALES WS

I can't align

Check that there are no obstacles of any kind interposed
between RX and TX and that the conditions of the site do not
represent an impediment;

Check that the power supply on the terminal board is
sufficient and that the batteries are charged;

Make sure there are no external light sources that interfere
with the correct reading of the signal (gate photocells, other
barriers, infrared etc.);

After accurately aligning the 
sensor (LED light on steady and 
continuous BEEP) the system 
remains in alarm

Make sure RX and TX have the same channel;

Make sure there are no external light sources that interfere
with the correct reading of the signal (gate photocells, other
barriers, infrared etc.);

Make sure that the other transmitters on the section have
been deactivated during the alignment phase;

The system goes into alarm with 
fog and rain

Make sure that the fog disqualification function is active;

Make sure that the structure is well sealed and check that
there are not already elements inside which could create
disturbance (water, insects etc.);

Check alignment is accurate and, if necessary, carry out the
procedure by performing a complete scan, making sure that
there are no light sources that can influence the calibration;

For more precise alignment, position one side of the Ales WS
cover in front of the lenses in order to have two surfaces
interposed between TX and RX to double the attenuation of
the beam;

Repeated false alarms

If possible, increase the intervention time.

Shield the cable from the radio transmitter to the ALES WS.

POLITEC | INSTALLATION MANUAL - VER.2.1

17. Product disposal.

All components of this barrier are an integral part of the equipment and must be disposed of
together with it.Just as with installation operations, also at the end of life of these products, the
dismantling operations must be carried out by qualified personnel.
These products are made up of various types of materials: some can be recycled and others must be
disposed of.Find out about available recycling or disposal systems for this category of products
governed by regulations in force in your area.

Warning!

- Some parts of the products may contain polluting or dangerous

substances which, if dispersed in the environment, could result in harmful effects
on the environment itself and on human health.As indicated by the symbol on the
side, it is forbidden to throw these products in domestic waste.Therefore, carry out
"separate collection" for disposal, according to the methods stipulated by the
regulations in force in your area or return the products to the seller when
purchasing a new equivalent product.

Warning!

- Local regulations can impose heavy penalties for incorrect disposal of

these products.

Содержание ALES WS





















Отзывы: