Polaris UTV 2x4 Series 11 Скачать руководство пользователя страница 83

Страница: 83 / 108

MAINTENANCE AND LUBRICATION

Brakes

Brake Inspection

The front and rear brakes are hydraulic disc type brakes and are

activated by the brake pedal. See page 33.
Routine inspections are recommended to keep the brake system in

good operating condition. Inspect the level of the brake fluid before

each operation.
Change the brake fluid at the intervals outlined in the Periodic

Maintenance Schedule beginning on page 54. The brake fluid should

also be changed if it becomes contaminated, if the fluid level is below

the minimum, or if the type and brand of the fluid in the reservoir are

unknown.

Inspection Procedure

1. Position the vehicle on level

ground.

2. Inspect the brake fluid by looking

at the reservoir (1) under the hood.

The level should be between the

upper (MAX) and lower (MIN)

level lines.

3. If the fluid level is lower than the

lower level line, add brake fluid to

the upper (MAX) line.

4. Apply the brake forcefully for a

few seconds and check for fluid

leakage around the fittings.

After opening a bottle of brake fluid, always discard any

unused portion. Never store or use a partial bottle. Brake

fluid is hygroscopic, meaning it rapidly absorbs moisture from

the air. The moisture causes the boiling temperature of the

brake fluid to drop, which can lead to early brake fade and the

possibility of accident or severe injury.

WARNING

Содержание UTV 2x4 Series 11













































































































Результаты поиска

Содержание UTV 2x4 Series 11

Отзывы:

Похожие инструкции для UTV 2x4 Series 11

Бренды по названию

Популярные бренды

Polaris UTV 2x4 Series 11, Руководство пользователя

Результаты поиска

Содержание UTV 2x4 Series 11

Отзывы:

Похожие инструкции для UTV 2x4 Series 11

Бренды по названию

Популярные бренды