Polaris Sportsman 9921344 Скачать руководство пользователя страница 95

Страница: 95 / 135

MAINTENANCE

Lights

Headlight Beam Adjustment

The headlight beam can be adjusted slightly upward or downward. Use
the following procedure to make the adjustment.

1. Position the vehicle on a level surface with the headlight approxi-

mately 25 ft. (7.6 m) from a wall.

2. Place the transmission in neutral.

3. Lock the parking brake.

4. Measure the distance from the floor to the center of the headlight

and make a mark on the wall at the same height.

NOTE:

Include rider weight on the seat when measuring.

5. Start the engine.Turn the headlight switch to high beam.

6. Observe the headlight aim on the wall. The most intense part of the

headlight beam should be two inches (5 cm) below the mark on the
wall.

7. Loosen the phillips screw at the rear of the headlamp.

8. Adjust the beam.

9. Tighten the screw.

25 ft.

(7.6 m)

2" (5 cm)

Содержание Sportsman 9921344








































































































































Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды

Polaris Sportsman 9921344, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды