Polaris Sportsman 9921344 Скачать руководство пользователя страница 100

Страница: 100 / 135

100

MAINTENANCE

Vehicle Immersion

If it's impossible to take your
ATV to a dealer before starting
it, follow the steps outlined
below.

1. Move the vehicle out of the

water.

2. Turn the fuel valve off.

3. Check the air box. If water is

present, dry the air box and replace
the filter with a new filter.

4. Remove the spark plug.

5. Loosen the carburetor drain screw

and drain the carburetor.

6. Turn the engine over several times

using the electric start.

7. Dry the spark plug. Reinstall the

plug or install a new plug.

8. Tighten the carburetor drain screw.

9. Turn the fuel valve on.

10. Attempt to start the engine. If necessary, repeat the drying proce-

dure.

11. Take the ATV to your dealer for service as soon as possible, whether

you succeed in starting it or not.

12. If water has been ingested into the PVT, follow the procedure on

page 103 for drying out the PVT.

CAUTION

If your vehicle becomes immersed, major engine damage can result if the

machine is not thoroughly inspected. Take the vehicle to your dealer before

starting the engine.

Drain

Screw

Содержание Sportsman 9921344








































































































































Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды

Polaris Sportsman 9921344, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды