Polaris Sportsman 9921344 Скачать руководство пользователя страница 34

Страница: 34 / 135

FEATURES AND CONTROLS

Switches

Mode/Reverse Override Switch

This vehicle is equipped with a reverse speed limiter system.To gain
additional power while backing, depress the override switch.

NOTE:

The override switch also allows activation of All Wheel Drive in

reverse, if the AWD switch is on. This switch is also used to toggle

through the modes of the rider information center. See page 44.

WARNING

Activating the override switch while the throttle is open can cause loss of con-

trol, resulting in severe injury or death. Do not activate the override switch

while the throttle is open.

Mode/Reverse

Override

Switch

Main Key Switch

Engine

Stop Switch

Headlight

Switch

All Wheel Drive

Switch

Содержание Sportsman 9921344








































































































































Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды

Polaris Sportsman 9921344, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921344

Отзывы:

Похожие инструкции для Sportsman 9921344

Бренды по названию

Популярные бренды