background image

Software Installation

YOUR TASK:

Install software onto your computer system to
enable the CD-ROM drive to operate optimally
within your specific operating system.

YOUR OBJECTIVE:

Enable your CD-ROM drive to communicate with
the rest of your computer system.

YOUR METHOD:

Identify your operating system and refer to the
section of this chapter, or the Plextor Manager
manual, that pertains to your operating system.

A device driver is a software program that allows your computer to interact with
your CD-ROM drive. If you do not use a device driver, or you use an outdated version
of the required device driver, you will not be able to operate your CD-ROM drive.
The lack of a device driver, or the use of an improper version of a device driver, are
the most common source of business for Plextor’s Technical Support Department.

For PC users with Windows 95: please see the Plextor Manager
manual.

For PC users with DOS/Windows: please see the Plextor Manager
manual.

For Apple computer users: please see page 37.

For PC users with IBM OS/2: please see page 38.

For PC users with Windows NT: please see page 39.

For SGI users who purchased Plextor’s SGI kit, please refer to the
instructions on the enclosed disc cover jacket.

---- CHAPTER 9 ----

36

  12PLEX OPERATION MANUAL

Содержание 12X-2





















Отзывы: