TC-SPD2000
DT Istr (TC-SPD2000) 05/18 – Rev 0_05/2018
13/16
The appliance turns on and the display will show "- -" in this mode is
emitted cold air.
Pressing the same button, the fan heater turns off automatically after 30 sec.
Select using the button the desired power heat
( = 1000W, = 2000W).
While the fan heater is in operation, with the button you can set the operating time (from a minimum of 1 h
up to a maximum of 12 h).
While the fan heater is operating press the button to activate the swing, press the same button to stop it.
1) Set the time /current day
Press the button once and the display will show "12", press / to set the hour.
Press again and the display will show "30", press / to set the minutes.
Press a third time to set the day of the week, always using the buttons / ,
then press to confirm. (NB. If the device is turned off or is disconnected the plug the time will reset)
2) Set the temperature
During operation press / to set the temperature (10 - 49°C) and then press to confirm.
After you set the temperature, the device will enter in "SMART MODE".
If T - T environment >2°C Operates at 2000W
If T - T environment <2°C Operates at 1000W
If T - T environment =0°C standby mode (turns on automatically with the temperature differences)
3) Set the weekly program
After you have set the time/current day, press the button , press to scroll through the weekly days selecting
on the display the desired day (D1-D7), press and the display will show P1-P6 (programs), press to set the
turn on desired time, press to set the torn off time desired and then press .
Detecting open windows
During operation, press , the display will show the temperature, adjust it with / .
In this mode if the temperature drops of 5-10°C in less than 10 minutes the appliance will enter into standby
mode in 30 minutes, press again to turn on again the appliance. To turn off the mode then repress .
LOCATION OF THE APPLIANCE:
Wall mounting
The unit must be fixed to the wall. Make sure that the opening of the air inlet is facing downward. The
appliance must be placed at a minimum height of 1.8 meters from the ground. Create two holes (same diameter
dowels) on the wall at the distance indicated in the DIMA present inside the packaging (39.8 cm). Insert the
screws into the anchors and hang the fixture.
The air outlet grid should have a minimum clearance of 1 m, while lateral sides must have a free space of at
least 40 cm.
WARNING: The appliance must be installed so that switches and other control devices can not be touched by a
person who is in the bathtub or in the shower.
SAFETY MEASURES
To avoid damages and dangerous situations caused by overheating, the fan heater is equipped with a safety
device that stops its operation in case of overheating, for example, due to a total or partial obstruction of the
grills. In this case, disconnect the appliance from the mains socket, wait for around 30 minutes so that it cools
down, and remove the object that is obstructing the grills. At this point, it is possible to start the appliance
again, as described above. The appliance should operate correctly. Should the problem come up again, contact
the nearest support centre.
MAINTENANCE
1.
This appliance requires no maintenance except cleaning of its external surfaces.
2.
Before cleaning the appliance, disconnect it from the mains socket and wait for it to cool down.
3.
Dust the intake grill regularly, removing threads, down or any other foreign matter that might limit regular
air circulation.
4.
To clean external surfaces, use only a soft cloth moistened with water, and do not use solvents.
5.
Do not throw the box, use it to store the equipment.
6.
When you don’t use the appliance, store it in its original packaging and store in a dry place.
INSTRUCTIONS FOR DISPOSAL
Disposal of this product shall be governed by the European Community Directive 2012/19/UE on Waste
Electrical and Electronic Equipment (WEEE). According to this regulation, the consumer has the
obligation NOT to dispose of this product as household waste but through separate channels of collection
