PleasureCraft Engine Group crusader Скачать руководство пользователя страница 38

36

L510001-05

25-HOUR ENGINE INSPECTION - 8

After the fi rst 25 hours of operation, it is recommended 
that the engine be given an inspection.  Your boat dealer 
or a Crusader servicing dealer should be contacted 
to perform the necessary checks and adjustments to 
ensure the proper engine performance.  The following 
maintenance should be performed:

 

•  Change the engine oil and fi lter.

 • 

 

Check and clean the primary fuel fi lter (returnless 
design fuel system only).

 

•  Check the engine alignment.

 • 

 

Inspect the accessory drive belt(s) and check the 
tension.

 

•  Check all the fl uid levels.

 • 

 

Check the throttle and the shift cable adjustments 
and check for freedom of movement.

 • 

 

Cooling System - Inspect all the hoses for leaks, 
damage and deterioration.  Check all the hose 
clamps for adequate tightness.

 • 

 

Exhaust System - Inspect the entire exhaust 
system for leaks, damage and deterioration.  
Check all the hose clamps for adequate 
tightness.

 • 

 

Battery - Check the electrolyte level and specifi c 
gravity.  Inspect the case for damage.  Check the 
battery cables and connections.

 • 

 

Engine Assembly - Check for loose, missing 
or damaged parts.  Pay close attention to 
engine mounts, starter and alternator mounting 
fasteners.

NOTICE: 

 Crusader Marine Engines assumes no 

responsibility for the costs related to the 25-hour 
inspection.  This is the owner’s responsibility.

Содержание crusader

































































































Отзывы: