PleasureCraft Engine Group crusader Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 96

PleasureCraft Engine Group crusader Скачать руководство пользователя страница 2

Welcome to the growing family of Crusader Marine Engines owners. We are delighted you have chosen Crusader
power for your boat and wish you many years of enjoyment.

READ THIS MANUAL THOROUGHLY

Before starting your engine(s), READ THIS MANUAL CAREFULLY AND COMPLETELY. If you do not understand
any portion of the manual, contact your Dealer for clarifi cation or assistance. Ask your Dealer for a demonstration of
actual starting and operating procedures.

The descriptions and specifi cations contained in this manual were in effect at the time of printing. Crusader Marine
Engines’ policy of continued improvement reserves the right to change specifi cations or design without notice and
without obligation.

This manual will cover the following Crusader engines:

Year

Model

2005

5.0L

MPI

2005

5.7L MPI

2005

6.0L MPI

2005

8.1L

MPI

2005

8.1L

MPI

(HO)

Part Number - L510001-05

Printed 12/04

«
1
2
3
4
...
»

Содержание crusader

































































































Отзывы:

Нет отзывов