background image

25

REMOTE CONTROL OPERATION

 

 

 

 

 

 

 

 

 

MULIT-FUNCTION WIRELESS REMOTE CONTROL SYSTEM 

FOR OPERATING A LATCHING SOLENOID VALVE, MANUALLY OR WITH A THERMOSTAT FUCTION 

 

 

 

 

 

INTRODUCTION 

This  remote  control  system  was  developed  to  provide  a  safe,  reliable,  and  user-friendly  remote  control  system  for  gas  heating 

appliances.  The system is operated manually from the transmitter.  The system operates on radio frequencies (RF) within a 20-feet 

range using non-directional signals.  The system operates on one of 1,048,576 security codes that are programmed into the transmitter 

at the factory; the remote receiver's code must be matched to that of the transmitter prior to initial use.  

 

 

Review COMMUNICATION SAFETY under GENERAL INFORMATION section.  This safety feature shuts down 

the appliance when a potentially unsafe condition exists. 

 

 

 

TRANSMITTER 

 

This remote control SYSTEM offers the user a battery-operated remote control to 

power  a  latching  solenoid  such  as  those  used  with  gas  valves  used  in  some 

heater rated gas logs, gas fireplaces and other gas heating appliances. 

 

The  solenoid  circuit  uses  the  battery  power  from  the  receiver  to  operate  a 

solenoid.  The circuit has reversing polarity software which reverses the positive 

(+)  and  negative  (-)  output  of  the  receiver's  battery  power  to  drive  a  latching 

solenoid ON/OFF. The SYSTEM is controlled by the remote transmitter. 

 

The transmitter operates on a (2) 1.5V AAA batteries.  

 

ALKALINE batteries should always be used for longer battery life and maximum 

operational performance. Re-chargeable batteries should not be used. 

 

Before  using  the  transmitter,  install  the  (2)  AAA  transmitter  batteries  into  the 

battery  compartment.  (Use  caution  that  batteries  are  installed  in  the  proper 

direction) 

 

 

 

 

 

KEY SETTINGS 

 

 

ON      - Operates unit to on position, Manually operated solenoid ON. 

      OFF      - Operates unit to off position, Manually operated solenoid OFF. 

      MODE  - Changes unit from manual mode to thermo mode. 

      SET      - Sets temperature in thermo mode. 

 

 

 

 

 

 

 

 

 

 

 

ON

MODE

OFF

SET

1

2

3

4

 

ON

MODE

OFF

BUTTON

WALL CLIP

SLOT

BATTERY

COMPARTMENT

FRONT

BACK

OFF

SET

ON

BUTTON

MODE

BUTTON

SET

BUTTON

 

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT 

ATTEMPT TO INSTALL OR OPERATE  

Содержание VFL2-MO24DR











Отзывы: