PLAYSTAR Play Maker PS 7456 Скачать руководство пользователя страница 34

Страница: 34 / 36

SLIDE – Mounting Instructions

Align Slide at right angle (90˚) to 48" play deck.

Lip of Slide should rest on the play deck

¹|x

Using the Slide as a template, mark

play deck through the three holes

in the Slide. Drill three

₈

" holes at

marked location.

Attach Slide temporarily to play deck with three

#14 x 1

₄

" screws provided.

Prepare level area where Slide touches ground

that is 1" below surrounding grade.

Locate and mark the ground on the back side,

on either side of the star. Remove Slide

and screw Playset Anchor into the ground

(a long screwdriver will help). Screw the

anchor deep enough so that the loop at the

top of the anchor will be flat against the back

surface of Slide when the Slide is in the final

position.

Reinstall Slide permanently, attaching it to play

deck using #14 x 1

₄

" pan head

screws provided.

Use the Playset Anchor as a drill guide and

drill a

³|₈

" hole completely through the Slide.

Attach Slide to anchor with one

³|₈

" x 1

¹⁄₄

hex bolt, two

³|₈

" washers and one

³|₈

" lock

nut provided in the anchor kit.

Fill in around bottom of Slide to make surface

level to surrounding grade.

Caution: Failure to anchor the Slide

properly could cause serious

injury from children lifting

the slide.

Caution: Do not install this Slide over

concrete, asphalt, packed

earth, or any other hard

surface. A fall onto a hard

surface can result in serious

injury to the equipment user.

1¹|x

Items for

STEP 40

(1) PS 8813 Scoop Slide
(3) #14 pan head screws

Содержание Play Maker PS 7456





































Результаты поиска

Содержание Play Maker PS 7456

Отзывы:

Похожие инструкции для Play Maker PS 7456

Бренды по названию

Популярные бренды

PLAYSTAR Play Maker PS 7456, Инструкция по безопасности и руководство по сборке

Результаты поиска

Содержание Play Maker PS 7456

Отзывы:

Похожие инструкции для Play Maker PS 7456

Бренды по названию

Популярные бренды