background image

3

INSTALLATION:

1.  Follow the instructions provided, do not  
 

alter its design in any way.

2.  Place the playset on level ground, not  
 

less than 6' (1.8m) from any structure  

 

or obstruction such as a fence, garage,  

 

house, overhanging branches, laundry  

 

lines or electrical wires. If the area  

 

where you will be installing your play- 

 

set is not level, you must make it level.

3.  Playsets must be anchored to the  
 

ground. Follow the anchoring instruc- 

 

tions provided with your building kit. If  

 

soil conditions permit anchors to be  

 

pulled out easily, such as in sandy soil  

 

conditions, cementing is required.

4.  Tighten all bolts securely to the intended  
 

member then cut off all protruding  

 

threaded ends of bolts with a hack saw  

 

flush to the end of the nut and  

 

remove sharp edges with a metal file.

WARNING: Children must not use the 
playset until properly installed and prop-
er shock-absorbing surfacing material is in 
place.

OPERATION:

   Observing and  

following statements and  warnings 
reduces the likelihood of serious or 
fatal injury.

1.  On-site adult supervision is recommended  
 

for children of all ages.

2.  Only one child, for each single planned  
 

seat or single planned activity should  

 

be allowed on this set at one time, with  

 

a maximum weight of 

105 pounds for  

 

each child

.

WARNING:  You must teach children the 
following:    
A. 

Not to walk close to, in front of, behind,  

 

or between moving items.

B. 

Not to twist swing chains or ropes or  

 

loop them over the top support bar since  

 

this may reduce the strength of the  

 

chain or rope.

C. 

Avoid swinging empty seats.

D. 

To Sit in the center of the swings with  

 

their full weight on the seats.

E. 

Not to use the equipment in a manner  

 

other than intended.

F. 

Not to get off equipment while it is in motion.

G. 

Not to climb when equipment is wet.

H. 

Not to attach items to the playground  

 

equipment that are not specifically  

 

designed for use with the equipment  

 

such as, but not limited to, jump  

 

ropes, clothesline, pet leashes, cables  

 

and chain as they may cause a  

 

strangulation hazard.

I. 

Remove bike or other sports helmet  

 

before playing on the play equipment  

 

as the helmet may become entrapped  

 

in an enclosed opening and cause a  

 

strangulation hazard.

3.  Verify that suspended climbing ropes  
 

are secured at both ends and that they  

 

cannot be looped back on themselves.  

 

(A rope that is not taut enough may  

 

cause a strangulation hazard.)

4.  Dress children appropriately. Provide  
 

well fitting shoes. Avoid ponchos,  

 

scarves, and other loose-fitting clothing  

 

which is potentially hazardous while  

 

using equipment.

5.  Verify that all suspended swinging  
 

components have at least 8" clear- 

 

ance between the lowest point of  

 

component and top of shock-absorbing  

 

surfacing material.

WARNING:  Lawn swings are designed for 
use by children two years of age and older. 
Use by children under the age of two can 
result in entrapment between the seat and 
backrest. 

NEVER place children in a rear-

ward facing position or with legs between 
the seat and backrest because the child’s 
body may pass through the opening 
causing entrapment of the child’s head. 

DISPOSAL:

When the playset is to be retired from 
service, disassemble and dispose of in 
such a way that no unreasonable 
hazards will exist. Follow your local  
disposal requirements.

At the beginning of play season:     Date: ___________

  n

 Tighten all hardware.

  n

 Lubricate all metallic moving parts per  

    manufacturer’s instructions.

  n

 Check all protective coverings on bolts, pipes, edges,  

   and corners. Replace if they are loose, cracked, or mising.

  n

 Check all moving parts including swing seats, ropes,  

    cables, and chains for wear, rust, or other  
    deterioration. Replace as needed.

  n

 Check metal parts for rust. If found, sand and repaint  

    using a nonlead-based paint meeting the  
    requirements of 16 CRF 1303.

  n

 Check all wood members for deterioration and  

    splinters. Sand down splinters and replace  
    deteriorating wood members.

  n

 Reinstall any plastic parts, such as swing seats or  

   any other items that were removed for the cold season.

  n

 Rake and check depth of loose fill protective  

    surfacing materials to prevent compaction and to  
    maintain appropriate depth. Replace as necessary.

Twice a month during play season:  Date: _________

  n

 Tighten all hardware.

  n

 Check all protective coverings on bolts, pipes, edges,  

   and corners. Replace if they are loose, cracked, or missing.

  n

 Rake and check depth of loose fill protective  

    surfacing materials to prevent compaction and to  
    maintain appropriate depth. Replace as necessary.

Once a month during play season:  Date: _________

  n

 Lubricate all metallic moving parts per  

    manufacturer’s instructions.

  n

 Check all moving parts including swing seats, ropes,  

    cables, and chains for wear, rust, or other  
    deterioration. Replace as needed.

At the end of each play season or when the  
temperature drops below 0º F:
        Date: _________

  n

 Remove plastic swing seats and other items as specified  

    by the manufacturer and take indoors or do not use.

  n

 Rake and check depth of loose fill protective  

    surfacing materials to prevent compaction and to  
    maintain appropriate depth. Replace as necessary.

SAFETY

ANNUAL MAINTENANCE CHECKLIST 

(Copy this section as needed and maintain for your records or visit www.playstarinc.com/maintenance)

If any of these conditions exist, call 1-888-752-9782 for ordering information.

Clean plastic components with warm water and a mild detergent such as dish soap.

.

Содержание Play Maker PS 7456





































Отзывы: