8/ 26/ 2008 3: 02: 36 PM, Rachel
Maintenance
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part is
broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Parts List - Deck Mount
-VARIES-
007117-L
007117-R
See Pg.
R5 - 11
9103062-TR
9103082-TR
9333002
9413002
Panel Frame (Rotomolded LDDPE)
Roto Panel Bracket Left
Roto Panel Bracket Right
Socket Clamp Assy.
Bolt Button Head 3/8" x 1-1/4"
Bolt Button Head 3/8" x 1-3/4"
Washer Flat 3/8" x 1" x .100 thick
Nut Lock 3/8"
PANEL ROUND/SQUARE R5 ROTO:
Shall be constructed of UV-stabilized, rotationally
molded, Linear Low Density Polyethylene with an
average single wall thickness of 1/4". The Panel Round
has a 26.5" Diameter opening and the Panel Square
has a 27.5" x 27.5" square opening. The Panels shall
be 38" x 43-1/2" x 3" deep.
SOCKET CLAMPS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy. The Socket Clamps have a
multi-stage baked-on powder coat finish.
ROTO PANEL BRACKET:
Shall be precision laser-cut and formed from 3/16"
sheet steel. The Roto Panel Bracket has a multi-stage
baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Specifications
1
1
1
2
2
4
12
6
Installation
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
PANEL - TYPE 1 (Rotomolded LLDPE)
R5 - 1601
Rev G
Page 3 of 3
Parts List - Ground Mt.
-VARIES-
See Pg.
R5 - 11
Panel Frame (Rotomolded LDDPE)
Socket Clamp Assy.
1
4
Step 1. *This Step is Pre-Assembled*
Insert Pipe(s) into Panel and Secure with Zinc Collars.
Refer to Figure 1 for hardware type and orientation.
Step 2.
Locate and mark the position of the Collars on the
Support Posts. Refer to Elevation View for Collar
locations. See Note C. See also Assembly Page R5 -
09 Collars for hardware type and orientation.
Step 3. - Deck Mount
Attach the Panel to the deck using the Roto Panel
Brackets Left and Right. Refer to Figure 1 for hardware
type and orientation.
Step 4.
Attach the Panel (Pipe) to the Post Collars using the
Socket Clamps. Refer to Figure 2 for hardware type
and orientation. See also Assembly Page R5-11
Socket Clamps for additional hardware details.
Step 5.
Apply liquid thread lock and fully tighten all fasteners
according to the "TIGHTENING TORQUE FOR
HARDWARE" Section of the Installer's Manual. See
Note A.
Step 6.
Place appropriate compliant protective surfacing under
and around Ground Mounted Panels. See Note D.
410001
FS-1600
9248112
9263022
Collar Zinc
Cut Panel Pipe Roto 1" x 38-1/8"
Screw Drywall #8 x 2 -1/2" WS
SQBH
Screw Soc Set 3/8" x 5/8"
4
2
8
4
Assembled Parts List -
Ground Mount
410001
FS-1600
9248112
9263022
Collar Zinc
Cut Panel Pipe Roto 1" x 38-1/8"
Screw Drywall #8 x 2 -1/2" WS
SQBH
Screw Soc Set 3/8" x 5/8"
2
1
4
2
Assembled Parts List -
Deck Mount
