background image

1

2

3

4

5

6

Front axle

Tools required: Spanner

Remove all the parts from the front axle.

1. Slide a 

Ø10 washer

 onto the 

front axle

.

2. Slide the 

bushing 

(ring end first) onto the 

front axle

.

3. Slide the 

normal wheel

 (with wheel hubcap) onto the rear axle. and keep the 

normal wheel

 match with the 

bushing

.

4. Slide a 

Ø10 washer

 onto the 

front axle

.

5. Tighten a 

Ø10 Locknut

 to the end of the 

front axle

 with a spanner.

6. “Snap” the 

hubcap

 to the wheel cover. 

    Repeat this step for the other side. 

GAP

    After assembling any wheel to the axles, please check the gap 
between the screw thread and the collapsible (refer to below picture), if 
the gap is too big, please add two or three washers inside the wheel, But 
after tightening the nut outside the wheel, please turn the wheel by your 
finger to check if the wheel can run smoothly, this is very important, 
because if the wheel can run smoothly, it is ok, but if the nut press the 
wheel and the wheel can’t run smoothly, the motor will be broken easily! 
Then you need to decrease one or two washers to make sure the wheel 
can run smoothly!

Attach the Front Wheels  

  10

Содержание MINI Hatch





























Отзывы: