Platinum Access Systems BLSL3060 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 34

background image

32

Gate Operator Trouble Shooting Procedure

c. Does Not Close Automatically:

-- Check TIMER pot to make sure the setting is correct, or not. Normally set to 12 O’clock.
-- Check other external safe devices like Loop Detector, Photo Beam sensor, Edge Sensor,

Radio to make sure none of them are activated.

3. Primary / Secondary Gate Configuration

a. Gates Open and/or Closes in Opposite Direction (Swing Gate).

-- Switch the OPEN DIR LEFT/RIGHT switch to the other direction.

b. Gates Do Not Close at the Same Time (Swing Gate).

-- Check the P/S SYNC pot to make sure it set to 12 O’clock. Then press reset button to reset the opera-
tors.

c. Gates Do Not Close in Preset Order (Swing Gates).

-- Check P/S SYNC pot to make sure the setting is correct. If it is correct, press rest button to reset the
operators.
-- Check DIR switch to make sure one operator is set to secondary.

d. Sometime One Gate is Much Slower than the Other Gate.

-- Please make sure that every external device only connects to the Primary gate operator. Nothing
should connect to Secondary gate operator. If any input device is connected to the Secondary unit,
please change it to connect to the primary unit. Then press Reset to rest the operators.

e. Gates Hit Each Other (Master/Slave Slide Gates

).

-- One gate over traveled. Make sure the limit nut has set correctly.
-- Please make sure the end user never use pad lock to lock the gates together. Only maglock can be

used to lock the gates. Please correct this problem then reset the operators.

4. Others

a. Gate does not open at times and Alarm is ON (Swing Gate).

-- Please make sure the arm position in set up correctly. Make sure the arm does not put a lot of pressure

on the output shaft when the gate starts to open.

b. Gate(s) Do not Open or Close and Alarm is O

N.

-- Please make sure the There is a 4-pin terminal plug into the J8 GUARD connector with a short wire

that short GND & ST

c. Operator Makes Beeping Sound.
-- Check battery. Battery voltage is low. Please make sure the battery breaker is ON, and the battery wire

connection is good, and the charge led light is ON on the main board.

-- If these steps are OK and the unit is still making the beep sound, then it is time to replace the batteries.

Please replace both batteries at the same time.

BLSL3060 Manual_Layout 1 6/21/2015 10:44 AM Page 34

«
...
31
32
33
34
»

Содержание BLSL3060



































Отзывы:

Нет отзывов

Похожие инструкции для BLSL3060

3280M-267 1/2HP

Бренд: Chamberlain Страницы: 36

Security+ 800ADR 1/3HP

Бренд: Anaheim Automation Страницы: 36

Бренд: Hamilton Beach Страницы: 8

Бренд: Roger Technology Страницы: 2

Бренд: Roger Technology Страницы: 16

Бренд: SOMFY Страницы: 32

Бренд: SOMFY Страницы: 72

Бренд: Westinghouse Страницы: 10

Бренд: Alutech Страницы: 82

AccessMaster Security+ M150

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

Бренд: Chamberlain Страницы: 96

Бренд: Chamberlain Страницы: 96

Бренд: Dea Страницы: 19

Бренд: Dea Страницы: 20

Бренд: Dea Страницы: 26

Бренд: Dea Страницы: 39

Бренд: Dea Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды