Platinum Access Systems BLSL3060 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

background image

3

Installation: entrapment protection

Contact Sensor Installation:

Only sensors compliant with UL 325 are recommended.

Contact

Sensor

Contact

Sensor

All Contact Sensors to

be wired in parallel

Non-Contact Sensors (Photoelectric Sensors) Installation:

One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists,

such as the perimeter reachable by a moving gate or barrier.

Install photoelectric sensors to protect

against any entrapment or safety conditions

encountered in your gate application.

We recommend the use of EMX IRB-325

photoeyes to comply with UL325.

Gate in Closed Position

Photo Beam

Unit

Reflector

Contact Sensor

Contact

Sensor

Potential Entrapment Area

Note: This type of installation DOES NOT reverse the gate all the way back to its limits when the sensors

are obstructed. This installation is only to protect against entrapment and to comply with UL325.

TX

EMX Model

IRB-325

Shown

Connection ‘1’ (C1)

Connection ‘2’ (NC1)

Consult the UL325 device installation manual for more detail information about the usage,

installation and maintenance of this device.

BLSL3060 Manual_Layout 1 6/21/2015 10:44 AM Page 15

«
...
12
13
14
15
16
...
»

Содержание BLSL3060



































Отзывы:

Нет отзывов

Похожие инструкции для BLSL3060

Бренд: Wayne-Dalton Страницы: 22

Бренд: Eagle Access Control Systems Страницы: 32

Бренд: International Door Closers Страницы: 2

Бренд: Genius Страницы: 28

Бренд: Motorline professional Страницы: 8

Бренд: Key Automation Страницы: 60

Бренд: Supeero Страницы: 8

Бренд: Chamberlain Страницы: 41

Бренд: Winco Страницы: 8

Security+ 4200DI

Бренд: Doit Страницы: 40

Бренд: Becker Страницы: 20

CanPRO 56050-()

Бренд: Nemco Страницы: 5

Бренд: APRI Страницы: 33

Бренд: TOPP Страницы: 60

Бренд: Napoleon Страницы: 16

Excelerator 3531835447

Бренд: Genie Страницы: 32

Бренд: Genie Страницы: 33

Бренд: tau Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды