manualshive.com logo in svg

PlasmaPart CUT 40 Air Start, Руководство пользователя и информационное руководство

Поделиться
Скачать
PlasmaPart CUT 40 Air Start Скачать руководство пользователя страница 4

PlasmaPart Limited Instructions © 2014 

© PlasmaPart Limited 2014 no part of these instructions may be reproduced without prior written consent 
    from PlasmaPart Limited 
 

3 

Specification 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Instruction Notes

 

 
1. Operating environment 

 
 

1.1 

The CUT40 can be operated in harsh weather conditions at temperatures of 
between -10 and +40 Degrees Centigrade and a Relative Humidity of 80%. 
 

1.2 

Do not place the machine in direct sunlight or operate it in the rain. 
 

1.3 

Keep the machine dry and avoid any contact with water. 
 

1.4 

Do not use the CUT40 in a dusty atmosphere or one containing a corrosive or explosive 
gas. 
 

1.5 

If the machine will not be used for a long period of time it should be returned to its original 
packing box and stored in a dry environment. 
 

1.6 

The CUT40 has an internal fan to cool the high power electronics and the entry and exit 
ventilators must not be obstructed. Ensure there is sufficient space in front and behind the 
machine for the forced air to circulate. 
 

1.7 

 Ensure the power cable is connected to a supply which has the correct voltage and 
 current rating. The CUT40 has a built in electronic control to adjust for different 
 mains voltage over a limited range. There is a label on the back of the machine 
 indicating the machine setting. Units supplied to the UK will be set for 220Vac  
 (190-255Vac) which is suitable for single phase supplies.  
 

The CUT40 will be seriously damaged if it is connected to a 415V Three Phase 
supply. 

 

1.8 

  Always stand the machine on a level surface to prevent the unit overturning. 
 

 

Supply Voltage 

1-ph AC 220±15% V 

Supply Frequency 

50~60 Hz 

Power requirement (at 40A) 

4.8 KVA (Max) 

Rated input current (at 40A) 

16 A (Max) 

No-load voltage 

230 V 

Output current range 

20-40 A 

Output voltage range 

88-96 V 

Duty cycle @ 40 Amps Output 

60% 

Efficiency 

85% 

Cut Width 

1.0 mm 

Arc striking model 

Touch 

Cos φ (

η

) 

0.93 

Air pressure 

60 psi 

Содержание CUT 40 Air Start



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды