PlasmaPart CUT 40 Air Start Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 18

PlasmaPart CUT 40 Air Start Скачать руководство пользователя страница 11

PlasmaPart Limited Instructions © 2014

Troubleshooting - Appendix 2

PROBLEM

POSSIBLE CAUSE

SOLUTION

Plasma arc
stops while
cutting

Hand too tense,
inadvertently releasing the
cut switch

Hold the torch lightly against the material being cut, don't
push down. Try and relax the hand.

Cutting speed too slow

Torch moved too far away
from material

Compressor unable to keep
up with air demand

Check air pressure gauge reading when cut stops.

Check air pressure is 60psi with cut switch pressed.

Check torch lead connections at unit and torch are tight.

Check torch hose is undamaged.

Check Black Shroud for fractures.

Check compressor, give the compressor time to recover
if making long cuts when using a smaller compressor.
Check the regulator fittings have been assembled
properly using PTFE tape.

Technical problem with the
unit

[email protected]

Sparks are
shooting upward
not downward
through the
material

Plasma arc not piercing
material

Torch travel speed is too fast

Check grounding clamp is making a good connection to
the material being cut and is tightly connected at the unit.
Clean a patch of material for clamp if rusty

Increase current

«
...
9
10
11
12
13
...
»

Содержание CUT 40 Air Start



















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды