manualshive.com logo in svg

PlasmaPart CUT 40 Air Start, Руководство пользователя и информационное руководство

Поделиться
Скачать
PlasmaPart CUT 40 Air Start Скачать руководство пользователя страница 16

PlasmaPart Limited Instructions © 2014 

© PlasmaPart Limited 2014 no part of these instructions may be reproduced without prior written consent 
    from PlasmaPart Limited 
 

15 

ELECTROMAGNETIC RADIATION 

Any person fitted with a heart pacemaker or other artificial life support system must not be 
permitted to be closer than 2m of any operational electrical cutting equipment. 

 

IGNITION OF COMBUSTIBLE MATERIAL 

Combustible materials are not to be used, stored or allowed to accumulate in the welding/cutting 
area. Sparks and molten metal from the cutting process can travel a long way. 

UNAUTHORISED USE (CUT 80/100/120 only) 

Always switch the machine OFF and turn off and remove the safety lock key before leaving the 
machine unattended. The torch will not light with the key switch set off. 

DANGER FROM PIPES, VESSELS AND CABLES 

Ensure any pipework to be cut is free from chemical contamination.  Some chemical elements 
could explode or create noxious fumes when heated to plasma cutting temperatures. 

Ensure any vessel or cylinder to be cut does not contain any flammable gas, fuel or pressure before 
cutting. 

Avoid working near to cables which may be live. 

Do not cut cable which has insulation, burning insulation could create noxious fumes. 

Keep the machine power cables and torch power connection away from the cutting area. 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание CUT 40 Air Start



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды