Planex SWP-0224FP Скачать руководство пользователя страница 93

Страница: 93 / 124

SWP-0224FP 24PORT L2 INTELLIGENT PoE SWITCH User’s Manual

Allows user to delete a community entry from community table.

CLI command : snmp community delete

Community entry (table index): <entry id to delete>

This action will delete all hosts in community string with 'delete

community'.

Are you sure? (y/n):[y] <y for ‘yes’; n for ‘no’>

[Reload]

Restores the previous saved settings from configuration file.

CLI command : snmp community retrieve

[Host IP Address] [Community]

A host entry contains a host IP address, network mask and its dedicated
community string.

CLI command : snmp host add

Host IP/Subnet: <IP address>

Netmask: <netmask>

Community: <community string>

User can modify a host entry in the table by reassigning its allowed IP address,
network mask and community string.

CLI command : snmp host set

Host table entry (table index): <entry id to config>

Host IP/Subnet (old IP address): <new IP address>

Netmask (old netmask): <new netmask>

Community (old community string): <new community string>

Allows user to delete a host entry from host table.

Содержание SWP-0224FP





























































































































Результаты поиска

Содержание SWP-0224FP

Отзывы:

Planex SWP-0224FP, Руководство пользователя, Страница: 93 / 124

Результаты поиска

Содержание SWP-0224FP

Отзывы: