Planex SWP-0224FP Скачать руководство пользователя страница 84

Страница: 84 / 124

SWP-0224FP 24PORT L2 INTELLIGENT PoE SWITCH User’s Manual

5.3.2

Physical Interface Commands

[Admin] [Enable/Disable]

Displays the port admin status and allows user to turn the port on or off.

CLI command : l2 port admin <port number> <enable/disable>

[Mode] [Auto/10M-Half/10M-Full/100M-Half/100M-Full/1G-Full]

Displays the current speed and duplex mode of the port. The speed and
duplex mode can be automatically detected when auto-negotiation is enabled
on a port.

CLI command : l2 port autoneg <port number> <enable/disable>

CLI command : l2 port speed <port number> <10/100/1000>

CLI command : l2 port duplex <port number> <full/half>

[Flow Control] [Enable/Disable]

Displays the IEEE802.3x flow control setting of a port. Note that this flow
control is operating only in full duplex mode.

CLI command : l2 port flow <port number> <enable/disable>

[Reload]

Restores the previous port settings from the configuration file.

CLI command : l2 port retrieve

5.3.3

Bridge Commands

[Spanning Tree is] [STP Enabled/ RSTP Enabled/ Disabled]

Allows user to specify whether the switch participates the Spanning Tree
Protocol (STP/ RSTP).

CLI command : l2 stp start <stp / rstp>

CLI command : l2 stp stop

Содержание SWP-0224FP





























































































































Результаты поиска

Содержание SWP-0224FP

Отзывы:

Бренды по названию

Популярные бренды

Planex SWP-0224FP, Руководство пользователя

Результаты поиска

Содержание SWP-0224FP

Отзывы:

Бренды по названию

Популярные бренды