Planex SWP-0224FP Скачать руководство пользователя страница 83

Страница: 83 / 124

SWP-0224FP 24PORT L2 INTELLIGENT PoE SWITCH User’s Manual

[Network Mask]

Displays the subnet mask for the switch.

CLI command: net interface ip sw0 < IP address> <netmask>

[Default Gateway]

Displays the IP address of the default gateway. This field is necessary if the
switch network contains one or more routers.

CLI command: net route static add <destination subnet/IP> <gateway>
<netmask> <metric>

[Password Protection is] [Enabled/Disabled]

When the password protection is enabled, the web interface will request a user
name and password authentication while user accesses the switch through the
browser.

CLI command : sys web set <enable/disable>

[New Password]
[Verify Password]

The default user name is admin. By default, a password is not required. You
may set a password by configuring these fields.

CLI command : sys users modify <user name, ‘admin’ by default>

user name (old user name, ‘admin’ by default): <new user name>

password (old password): <new password>

[Reboot]

User can reboot the switch by issuing the reboot command.

CLI command: sys reboot

[Upload]

No CLI command for this function. Refer to Boot ROM commands for this
function.

Содержание SWP-0224FP





























































































































Результаты поиска

Содержание SWP-0224FP

Отзывы:

Бренды по названию

Популярные бренды

Planex SWP-0224FP, Руководство пользователя

Результаты поиска

Содержание SWP-0224FP

Отзывы:

Бренды по названию

Популярные бренды