manualshive.com logo in svg

Planeta PKB Series, Руководство по эксплуатации и обслуживанию

Операционно-техническое руководство для продукции серии Planeta PKB доступно для загрузки бесплатно на manualshive.com. Это исчерпывающее руководство содержит информацию о эксплуатации и техническом обслуживании оборудования. Скачайте его сейчас, чтобы получить подробные инструкции по использованию вашего устройства.

Поделиться
Скачать
background image

9

Q

A

FO

.2

13

1.

EN

.A

D

R

 0

0/

V

L/

15

 

3  General information 
This manual describes an PLANETA hoist trolley unit for heavy duty use in an industrial environment. 

 

3.1  Technical specification 
If deviating specification are applicable, then the technical specifications can be found in Appendix 

II “Technical specifications”, and may contain one or more of the following items: 

‐ 

Scope of supply, data & specifications 

‐ 

General hoist and trolley data 

‐ 

Mechanical specifications & surface treatment 

 

3.2  Factory warranty 

The warranty period of the product, as specified in the technical specification, becomes invalid if: 

‐ 

The instructions in this manual for installation, operation, inspection, 

maintenance, storage, transport etc. are not followed. 

‐ 

Repairs and eliminations of faults are executed without been consulted and 

approved by PLANETA. 

‐ 

Repairs and eliminations of faults are executed by incompetent persons. 

‐ 

The product is modified or non-original spare parts are used. 

‐ 

The product is improperly used. 

If any question arises concerning the warranty, contact your local authorised reseller or your 
contact person at PLANETA. 

 

3.3  Safe Working Load 
The design is based on the safe working load specified in the technical specification of the product. 
It is the operator’s responsibility not to go beyond what is permitted. The maximum permitted 
working load, indicated in kilograms or metric tons, can be found on the nameplate. 

 

Standard headroom and low headroom hoist trolley units can optionally be executed with an 
overload protection device. Ultra low headroom hoist trolley units always have the overload 
protection device built in. If equipped with an overload protection device, the slipping clutch will be 
activated between 125% and 150% of the safe working load. When activated, the hoist can only be 
lowered to reduce the load below the safe working load. 

 

3.4  Areas of application 
Model K hoist trolley units are designed to withstand ambient temperatures of -20°C to +40°C 
and humidity up to 100%, but not submerged in water. 

 

Model N hoist trolley units are designed to withstand ambient temperatures of -15°C to +40°C 
and humidity up to 90%. 

 

If the hoist trolley unit is continuously used in a high humidity environment with temperature 
fluctuations, there is a chance that condensation occurs which may reduce the lifespan of the hoist 
trolley unit. The maximum designed longitudinal slope of the traveling surface is 0.17

°

. When the 

hoist trolley unit is frequently used in an outside environment, it shall be protected against the 
effect of weather for example: rain, hail, snow, direct sunlight, dust, etc. 

 

 

Danger! Hoist trolley units may not be used for transport of persons. 

 

 

Danger! Hoist trolley units are not designed for use in potentially explosive 

atmospheres. 

 

Hoist trolley units can optionally be executed for use in other circumstances. For example: 

‐ 

Dusty, greasy and/or high humidity environments. 

‐ 

Offshore and/or corrosive environments. 

‐ 

Potentially explosive atmospheres (Ex areas). 

‐ 

Food industries. 

‐ 

Use in extreme high or low temperatures. 

 

 

 

9 

Содержание PKB Series





















































Отзывы:

Нет отзывов

Похожие инструкции для PKB Series

TBEI Rugby LR-416B Installation And Operation Manual preview
Rugby LR-416B
Бренд: TBEI Страницы: 22
RED ROOSTER TCS-980-AT2S User Manual preview
TCS-980-AT2S
Бренд: RED ROOSTER Страницы: 72
Far Tools CH 2T Manual preview
CH 2T
Бренд: Far Tools Страницы: 28
Raptor PT Series Operating & Maintenance Instructions preview
PT Series
Бренд: Raptor Страницы: 18
HADEF 22/90 Installation, Operating And Maintenance Instruction preview
22/90
Бренд: HADEF Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды