Planeta PKB Series Скачать руководство пользователя страница 22

Страница: 22 / 52

Option B2,

‐

Disassemble and remove a section of the monorail.

‐

Lift the hoist trolley unit next to the end of the monorail with the underside of the

wheels just above the bottom flange of the monorail.

Attention! Watch for the orientation of the hoist trolley unit.

‐

Push the hoist trolley unit onto the monorail.

‐

Reinstall the earlier removed section of the monorail.

‐

If disassembled, reinstall the end stops on the monorail.

Option B3,

Preforming this step will make a section of the monorail permanently unusable. If this

option is not desirable, follow option B4.

‐

Cut away the lower flange of a unused section of the monorail. Preferably at the

end of the monorail.

‐

Lift the hoist trolley unit to just below the removed section.

‐

Slowly lift the hoist trolley until the monorail web is in between the wheels and

the underside of the wheels are just above the bottom flange of the monorail.

Attention! Watch for the orientation of the hoist trolley unit.

‐

Push the hoist trolley unit onto the monorail.

‐

Reinstall the end stops on the monorail just beyond the removed section.

Option B4,

‐

For low headroom and ultra low headroom hoist trolley units, a special designed

suspension set can be ordered to install the hoist trolley using the procedure as

described in option B for a standard headroom hoist trolley unit.

After performing option A or B the following actions shall be taken:

‐

Check the position of the end stops on the monorail.

‐

Check if the safety latch is closed correctly.

‐

Check the lubrication of the hoist trolley unit according to chapter 8.2

“Lubrication list”.

Attention! After installation, the hoist trolley unit shall be commissioned and load tested

according to chapter 6 “Commissioning”.

Содержание PKB Series





















































Результаты поиска

Содержание PKB Series

Отзывы:

Похожие инструкции для PKB Series

Бренды по названию

Популярные бренды

Planeta PKB Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PKB Series

Отзывы:

Похожие инструкции для PKB Series

Бренды по названию

Популярные бренды