Planet FT-902 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

Planet FT-902 Скачать руководство пользователя страница 15

-12-

3.2.2 Login the media converter

Before you start configure the FT-90X, please note the FT-90X is configured through an Ethernet connection, make sure
the manager PC must be set on same the

IP subnet address

. For example, the default IP address of the FT-90X is

192.168.0.100

, then the manager PC should be set at 192.168.0.x (where x is a number between 2 and 254), and the

default subnet mask is 255.255.255.0. Use Internet Explorer 6.0 or above Web browser. Enter IP address

http://192.168.0.100

(the factory-default IP address) to access the Web interface.

When the following login screen appears, please enter the default username and password (default user name and
password is

"admin")

. Press Login to enter the main screen of FT-90X. The login screen in Figure 3-1 appears.

Figure 3-1

Login screen

#

Note

:

1. For security reason, please change and memorize the new password after this first setup.

2. Only accept command in lowercase letter under web interface.

«
...
13
14
15
16
17
...
»

Содержание FT-902









































Отзывы:

Нет отзывов