background image

29 

2)

 

Manually, selecting the file with the new firmware version (Section 4.9.3). New versions 

come available for free download from our websit

http://www.planarchel.ru/

 in the 

section that describes IT-19C analyzer. 

4.9.2

 

Updating Firmware Via Internet 

To use this function, the device firmware update check must be enabled in the 

ViewIt19C

 settings.

 

 

To update the firmware via Internet: 

1)

 

Connect the device to the 

ViewIt19C

 program

 

(Sections 4.8.2, 4.8.4).  

2)

 

After connecting the Analyzer, the program will automatically check for updates. If a 

new firmware version is detected, it will offer to update. To perform the update, follow 
the wizard. 

If the process was interrupted while loading the program  to the Analyzer, you should repeat the 
program update process. 

After  the  update  is  completed,  there  will  be  a  message  on  the  computer  screen  claiming  the 
update completion success. The Analyzer will reboot and start working as if it has just been turned 
on. 

4.9.3

 

Manual Firmware Updating 

To update the Analyzer firmware manually, follow the steps below:  

1)

 

connect the device to the 

SoftManager

 program (Sections 4.8.3, 4.8.4). To start 

SoftManager

 from 

ViewIt19C

, switch to firmware update mode in PC software.  

2)

 

Select the file with the device firmware (* .bsk2): click  

 (Figure 4.22) and select the 

file in a standard Windows file selection window. 

3)

 

Click 

«Update»

 button and wait for the update to complete.  

If  the  process  was  interrupted  while  loading  the  firmware  to  the  Analyzer,  you  must  repeat  the 
firmware update process. 

The update process completion is the same as during the updating via Internet. 

4.9.4

 

Emergency Firmware Update 

An emergency software update procedure is provided if the main device program is damaged and 

does not allow the user to enable the PC mode 

. To call out the update procedure, make sure 

that the device is switched off, press and  hold «

», turn on the power by pressing «

» or by 

applying external power. The program status bar update mode will appear on the display: 

IT-19C Bootloader v1.1. 

To update the device firmware, perform actions described in section 4.9.3.

 

 

Содержание IT-19C

































Отзывы: