Wireless Flash Shooting: Radio (2.4G
Hz
) Transmission
Wireless Multiple Flash Shooting
You can divide the slave units into two or three groups and perform TTL autoflash while
changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode
for each firing group.
• Auto Shooting with Two Slave Groups
• Auto Shooting with Three Slave Groups
1.
Press < > Button to enter C.Fn menu. The “Ver x.x” in the top-right corner refers to the software
version.
2.
Select the Custom Function Signs.
* Turn the Select Dial to select the Custom Function Signs.
3.
Change the Setting.
* Press<SET> button and the setting signs are highlighted.
* Turn the Select Dial to set the desired number. Press <SET> button will confirm the settings.
4.
Exit C.Fn Menu.
* Press < > Button to exit.
C.Fn: Setting Custom Functions
Custom
Function Signs
COLOR
SLAVE
MODEL
STANDBY
LIGHT
DELAY
UNITS
ALT
LCD
STEP
RESET
TIMES
Functions
Stable color
temperature
S1/S2 mode
selection
Modeling lamp
Auto power off
Backlighting time
Delay flash
Total number
of flashes
Triggering times
LCD contrast
Flash output
display
Parameter
resetting
Record of flash
Setting Signs
ON
OFF
OFF
S1
S2
CONT
INTER
OFF
30min
60min
90min
120min
15sec
OFF
ON
OFF
,
0.01~30S
-3~+3
OFF
01-99
1/256
2.0
NO
YES
XXX
XXX
Restrictions
M Non high-
speed mode
M mode
No
No
No
M/Multi mode
M mode
M mode
Non TTL mode
No
No
Settings & Descriptions
ON
OFF
OFF
S1 mode
S2 mode
Continuous lighting
Off after finishing the flash recycle
OFF
Auto power off without
any operation
Off in 15 sec.
Always off
Always lighting
Can be triggered as second curtain
Use UNITS in combination with
ALT: UNITS sets the total
number of flashes; ALT sets
the triggering times before
flash’s firing
7 levels
off
Choose from 01 to 99
Display in the form of fraction
Display in the form of decimal
Reset
Flash times
High-speed sync
flash times
2~4
Wireless mode
Wireless ID
ID
1- 4
- 43 -
- 44 -
A
B
A
B
C
H1200P
H1200P
H1200P
1.
2.
Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G
wifi router, Bluetooth, etc.)
→
To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the
channel which is not disturbed. Or turn off the other 2.4G equipment in working.
Please make sure that whether the flash has finished its recycle or caught up with
the continuous shooting speed or not(the flash ready indicator is lighten) and the
flash is not under the state of over-heat protection or other abnormal situation.
→
Please downgrade the flash power output. If the flash is in TTL mode, please try to
change it to M mode(a preflash is needed in TTL mode).
3.
Whether the distance between the flash trigger and the flash is too close or not
→
Please turn on the “close distance wireless mode” on the flash trigger (
＜
0.5m):
ST-III:
press the test button and hold on, then turning it on until the flash ready
indicator blinks for 2 times.
ST-IV
: Set the C.Fn-DIST to 0-30m.
4. Whether the flash trigger and the receiver end equipment are in the low battery
states or not
→
Please replace the battery(the flash trigger is recommended to use 1.5V disposable
alkaline battery).
The Reason
s
& Solution
s
For Misfiring with Wireless Triggering
