2
POWER
1
Part Names and Displays
Connecting The Wires
Analog Display
Analog Display
Display RPM and Motor RPM data.
2
Needle
Shows the current values and peak value.
3
Switch
Display switches between types.
4
Digital Display
Digital Display
Use to change modes of digital display
and reset the peak value.
Unit
4-pin
Connector
Meter
Holder
6-pin
Connector
5-pin
Connector
5
Illumination
(night illumination)
6
Display Range
Red
Dial & Needle : White or Blue
Backside
of the
meter
Diagnostic
Monitoring
Connector
Placement Diagram for Diagnostic Monitoring Connector
[ Meter ]
(Switchable)
[ Unit ]
(View from Gauge Connection)
(View from Car Connection)
7
10
Meter connector
Connect gauge cable
8
Spare
No need to use
9
Power connector
Connect OBD cable
7
8
9 10
Size
[Unit
：
mm]
ø60
15 30
70
50
Depth
22
Unit
Meter
ø65
(1.5 m)
(0.5 m)
1
2
3
4
Analog Display
Digital Display
TOYOTA
HONDA
Ready
Mode
At the right foot of the driver seat (with lid)
At foot of driver seat in the center
At the left foot of the driver seat (with lid)
Water Temp
[-35–150
°
C ]
Voltage
[ 8–18 V ]
Motor RPM
[0–32000rpm]
RPM
[0–8000rpm]
Motor RPM
[0–9000rpm]
Normally illuminated when on display
and Three-step dimming.
Note: Not display Motor RPM on Analog Display
when the Meter displays RPM by needle. See
the Digital Display to check the Motor RPM.
Turn the power switch to Ready Mode.
Insert the OBD Connector to the Diagnostic Monitoring
Connector.
Insert the 4-pin Connector to the backside of the meter.
Insert the 5-pin Connector of Gauge Cable and 6-pin
Connector from the Power Cable to the Unit.
Notes about using the OBD Connector
If you unable to get a grip
on the distended portions.
M a k e s u r e t o g r i p t h e
distended portions when
pulling it out or inserting it.
D o n o t p u l l o n t h e w i r e s
when trying to remove the
connector; the wires may
become disconnected.
CAUTION
W i t h s o m e c a r m o d e l s i t
m ay b e d i f f i c u l t t o g e t a
good grip on the connector.
In such case, pull
out the connector
by p u l l i n g o n t h e
end of the zip tie.
The meter start-up and stop is differ in power connection method.
IGN Cable
＝
Cut Connector
IGN
(12V with Key Switch ON)
OBD Cable
Diagnostic
Monitoring
Connector
Yellow
Yellow
Red
Linked to the ECU
Linked to the power switch
Normal
IGN
(using IGN Cable)
(not using IGN Cable)
1
2
3
How to use the Cut Connectors
10 mm
10 mm
When crimping, please
use crimpers or use pliers
to bend and then solder
together.
Pe e l of f of t he v inyl
cover at connection.
Peel off of the vinyl cover at
the end of the product’s wire.
Wrap around both
wire coils.
4
Close tightly with
cut connector.
5
Insulate with vinyl
tape.
Unplug the connector of
Yellow
and
Red
cable of OBD Cable and
connect
Yellow
cable of IGN Cable into the connector on
Yellow
cable,
then connect to IGN cable to IGN of car. (Do not connect to Acc)
(See Note)
1
2
3
4
4
