background image

49/72

EN

the air supply pressure must never be over 7 bar or 
below 2 bar.

when using the pump with aggressive or toxic liq-
uids or with liquids that may represent a health haz-
ard you must install suitable protection on the pump 
to contain, collect and signal any spills: danger of 
pollution, contamination, injuries and/or death. 

 installing the pumps without on-off valves on the 
intake and delivery sides to intercept the product in 
case of spillage is forbidden: danger of uncontrolled 
product spillage.

installing the pumps without on-off, three-way or 
check valves on the air supply piping to prevent the 
pumped liquid from entering the pneumatic circuit if 
the diaphragms are broken is forbidden: danger of 
fluid entering the compressed air circuit and being 
discharged into the environment.

should the user think that the temperature limits 
set  forth  in  this  manual  may  be  exceeded  during 
service, a protective device must be installed on the 
system  to  prevent  the  maximum  allowed  process 
temperature from being reached. If exceeded, re-
spect of the maximum temperature marked cannot 
be guaranteed.

the pumps must always be grounded irrespective 
of any organ to which they are connected. Lack of 
grounding  or  incorrect  grounding  will  cancel  the 
requirements for safety and protection against the 
risk of explosion. 

the  use  of  pumps  made  with  non-conductive 
material,  which  become  charged  with  static,  and 
without suitable grounding for flammable liquids 
is forbidden: risk of explosions due to static charge.

aggressive, toxic or dangerous liquids may cause 
serious injuries or damage to health, therefore it is 
forbiffen to return a pump containing such products 
to the manufacturer or to a service center. You must 
empty the internal circuits from the product first and 
wash and treat it.

pumps containing aluminium parts or components 
coming  into  contact  with  the  product  cannot 
be  used  to  pump  III-trichloroethane,  methylene 
chloride  or  solvents  based  on  other  halogenated 
hydrocarbons: danger of an explosion caused by a 
chemical reaction. 

the pump must not be used with fluids that are not 
compatible with its construction materials or in a 
place containing incompatible fluids. 

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

Содержание MA






































Отзывы: