Pitney Bowes OFFICERIGHT DI200 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 49

background image

4

Offi ceRight™ DI200 Operator Guide (SV41289-OG Rev. C)

Safety

•

Please read all the instructions in this manual

before you attempt

to operate your Offi ceRight™ DI200. Save all instructions.

WARNING!

Always use the power cord sup-

plied with your machine and plug it into a

prop-

erly grounded wall outlet that’s located near the
machine and easily accessible. Failure to properly

ground the machine can result in severe personal
injury and/or fi re.

•

DO NOT use a wall outlet controlled by a wall switch or one that
is shared with other equipment.

•

Do not use an adapter plug on the line cord or wall outlet.

•

Do not remove the ground pin from the line cord.

•

Make sure the area in front of the wall outlet into which the ma-
chine is plugged is free from obstruction.

•

DO NOT route the power cord over sharp edges or trap it be-
tween pieces of furniture. Make sure there is no strain on the
power cord.

•

To reduce the risk of fi re or electrical shock, DO NOT attempt to
remove covers or disassemble the inserter. The cabinet encloses
hazardous parts. Refer servicing to qualifi ed personnel.

•

Keep fi ngers, long hair, jewelry and loose clothing away from
moving parts at all times.

•

Never reach into the machine while it is running. Avoid touching
moving parts or materials while the machine is in use. Before
clearing a jam, be sure all machine mechanisms come to a com-
plete stop.

•

Know your equipment, especially

how to stop it in the event of an

emergency.

•

When removing jammed material, avoid using too much force to
protect against minor personal injury and damage to the equip-
ment.

• Use the equipment only for its intended purpose.

• Always follow the specifi c occupational safety and health stan-

dards prescribed for your workplace.

CAUTION!

If you relocate an Offi ceRight™ DI200

that has the optional Second Sheet Feeder A2
installed, remove it from the Second Sheet Feeder

fi rst—that is, as you lift it clear, make sure it fully
disengages from the Second Sheet Feeder. Obtain
help if necessary.

Important Safety Information

1. INTRODUCTION

«
...
2
3
4
5
6
...
»

Содержание OFFICERIGHT DI200


















































Отзывы:

Нет отзывов

Похожие инструкции для OFFICERIGHT DI200

Бренд: Harmar Mobility Страницы: 16

Бренд: Qingdao Desiree Страницы: 22

HS 300 LARGE | FH

Бренд: R. Beck Maschinenbau Страницы: 42

Бренд: Brewtools Страницы: 7

Бренд: morse Страницы: 6

Бренд: morse Страницы: 6

Бренд: Audipack Страницы: 19

Бренд: Hiniker Страницы: 47

Бренд: Walmag Страницы: 60

Бренд: Jema Autolifte Страницы: 22

Бренд: Hofmann Страницы: 19

Mobile Lift Pro II 70

Бренд: HAGOR Страницы: 12

Бренд: Dash Страницы: 11

Бренд: Haulotte Group Страницы: 104

Бренд: Unilift Страницы: 25

Бренд: Ravaglioli Страницы: 84

Бренд: morse Страницы: 7

Бренд: Philips Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды