Pitney Bowes OFFICERIGHT DI200 Скачать руководство пользователя страница 35

Страница: 35 / 49

Offi ceRight™ DI200

Operator Guide (SV41289-OG Rev. C)

Message

Meaning and Action

CANNOT

No sheet feeder has been selected in the job setup.

SHIFT

The display automatically times out from this message

ADDRESS

after two seconds and moves on to the turn double

ON INSERTS

detect On/Off menu function.

The machine has detected that the front cover D is

COVER D

open.Check that cover D is closed properly.

The machine detected that the rear cover E is open.

COVER E

Check that cover E is closed properly.

CHECK AREAS

Check for an unsuccessful clearance of a jam between

A1 & D

the sheet feeder A1 and the collation area. Remove the

paper in sheet feeder A1, open front cover D and check

that the machine is clear of material. Close front cover

D, reload and start run.

CHECK AREAS

This could be due to an unsuccessful clearance of a

A1, A2 & D

jam between the sheet feeders A1, A2 and the collation

area. Remove the paper in sheet feeders A1, A2, open

front cover D and check that the machine is clear of

material. Close front cover D, reload and start run.

CHECK / CLEAR

Inserts failed to feed. Check that the side guides in

INSERT FDR C

feeder C are not too tight. Reload feeder C and start run.

CHECK SHEET

Sheet feeder A1 out of paper, failed to feed or a jam

FEEDER A1

was not cleared successfully from this area. Remove

the paper in sheet feeder A1, reload and start run.

Reference

5. REFERENCE

Error Messages

Содержание OFFICERIGHT DI200


















































Результаты поиска

Содержание OFFICERIGHT DI200

Отзывы:

Похожие инструкции для OFFICERIGHT DI200

Бренды по названию

Популярные бренды

Pitney Bowes OFFICERIGHT DI200, Руководство оператора

Результаты поиска

Содержание OFFICERIGHT DI200

Отзывы:

Похожие инструкции для OFFICERIGHT DI200

Бренды по названию

Популярные бренды