PISCO VTA Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

PISCO VTA Series Скачать руководство пользователя страница 23

http://

www

.

pisco.co

m

3. Handling of product

①. The pneumatic equipments shall be handled by a person having

enough knowledge and experiences. Improper use of compressed air is
dangerous. Assembly, operation and maintenance of machines using
pneumatic equipment should be conducted by a person with enough
knowledge and experience.

②. Do not operate machine / equipment or remove pneumatic equipment

until safety is confirmed.

(1). Make sure that preventive measures against falling work-pieces or

sudden movements of machine are completed before inspection or
maintenance of these machine.

(2). Make sure the above preventive measures are completed. A

compressed air supply and the power supply to the machine must be
off, and also the compressed air in the systems must be exhausted.

(3). Restart the machines with care after ensuring to take all preventive

measures against sudden movements.

③. Do not disassemble or modify PISCO products, which affect the

performance, function, and basic structure of the product.

④. Take safety measures such as providing a protection cover if there is a

risk of causing damages or fire on machine / facilities by a fluid leakage.

⑤. Do not touch the release-ring of push-in fitting when there is a working

pressure.

⑥. Frequent switchover of compressed air may generate heat, and there is

a risk of causing burn injury.

⑦. Avoid any load on PISCO products, such as, a tensile strength, twisting

and bending. Otherwise, there is a risk of causing damage to the
products.

⑧. Do not use PISCO products for applications where threads or tubes

swing / rotate. The product can be damaged in these applications.

⑨. Do not force the product to rotate or swing even its resin body is

rotatable. It may cause damage to the product and a fluid leakage.

⑩. Do not supply excessively dry air to products. It may cause malfunction

due to a deterioration of rubber parts.

⑪. Do not wash or paint products with water or solvent. Solvent may

damage a resin body, or painting may cause malfunction.

⑫. The product incorporating NBR as seal rubber material has a

risk  of  malfunction  caused  by  ozone  crack.    Ozone  exists  in  high
concentrations  in  static  elimination  air,  clean-room,  and  near  the  high-
voltage motors, etc.  As a countermeasure, material change from NBR
to HNBR or FKM is necessary. Consult with PISCO for more information.

⑬. Do not stand on a product, or put anything on it. It may cause falls,

personal injury or damage to the product.

«
...
21
22
23
24
25
...
»

Содержание VTA Series





























Отзывы:

Нет отзывов