PISCO VG Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 21

PISCO VG Series Скачать руководство пользователя страница 11

116

VN

VZ

VQ

VX

VJ

VK

VG

VACUUM

GENERATOR

EXTERNAL VACUUM

CONTROLLER

VACUUM

PAD

VACUUM

ACCESSORIES

■ Manual of Vacuum Sensor

■ Adjusting Method of Blow-off Air

■ Attaching / Detaching Individual Plug-in Connector

P

Air rate: Reduce

Air rate: Increase

Blow-off air rate adjustment needle
Locknut

(～)Blue (～)Blue

＋

－

(Black)

0V

(Red)

＋

V

Note) ( ) is the lead color.

■DC24V

■AC100V

■Backside of connector

Latch

(Latch) 0V

(Red) ＋V

1. Pressure Adjustment

　①

Turn on the power (Apply DC power to the vacuum sensor after making sure the correct wiring).

　②

Fully turn the hysteresis setting trimmer (HYS) in the counter-clockwise direction in order to minimize the
hysteresis setting. (Vacuum sensor with analog output (Code: -NA) only)

　　

　　

Note) When vacuum level is not stable, minimized hysteresis make the output unstable.

　③

Adjust the vacuum setting trimmer (S1 / S2 and SW) to meet the required value.

　　

Note) Use a vacuum gauge or check in the actual system for setting pressure.

　④

Apply the air pressure and check the operation.

　　

(In case of Vacuum sensor with analog output (Code: -NA))

　　

Switch output (SW): Operation indicator (Red LED) turns ON more than the set pressure.

　　

(Vacuum sensor with 2 switch output (Code: -NW))

　　　

Switch output 1 (S1): Operation indicator (Red LED) turns ON more than the set pressure.

　　　

Switch output 2 (S2): Operation indicator (Green LED) turns ON more than the set pressure.

2. Differential response setting (Vacuum sensor with analog output (Code: -NA) only)

　①

Differential response setting can be adjusted by the hysteresis setting trimmer (HYS).

　②

Differential response setting range is regulated within about 0-15% of the set value. Differential response

setting becomes large when the trimmer is turned in the clockwise direction.

　③

Confirmation of Hysteresis

　　

Gradually increase and decrease the supply pressure around the set pressure value and read the value
from a vacuum gauge when operation indicator lamp turns ON/OFF. The difference in the displayed
values is taken as differential response.

　④

Hysteresis adjustment is useful for the following cases:

　　・

Increase differential response when pressure pulsates with output repeatedly showing small on/off movements.

　　・

When an allowable range is to be set for the lowering of pressure.

■

Adjusting Method of Blow-off Air

　

●

Turn the release needle in the clockwise direction to reduce

blow-off air and counter-clockwise to increase.

　　※

After adjustment of the blow-off air rate, make sure to

tighten the locknut to prevent the setting from changing
with attentions to the following

①

and

②

.

①

Without turning the needle, finger-tighten the lock nut clockwise until it touches needle-guide. Then

tighten the nut by turning 20 ~ 30

°

more by using proper tool.

②

Be careful not to damage the thread by over tightening.

■

Attaching / Detaching Individual Plug-in Connector

　

●

Insert the connector into the socket until it stops.

■

Connector Detaching Method

　

●

Pull out the connector while pushing the latch to

the arrowed direction.

«
...
9
10
11
12
13
...
»

Содержание VG Series






















Отзывы:

Нет отзывов