manualshive.com logo in svg

Piscine Solide V35046, Руководство по установке

Поделиться
Скачать
Piscine Solide V35046 Скачать руководство пользователя страница 45

No Diving or Jumping.  Observe all Safety Rules

Section

3

3-7

GENERAL INSTRUCTIONS - ROUND POOLS

ASSEMBLING THE POOL WALL

Section

3

C. INSTALL THE POOL LINER

1. Set the liner in place

a.  Open the carton. Do not use anything sharp to open the 

carton.

b.  Unpack and unfold the liner and spread it out in the sun 

to warm it up. Inspect all the seams and surfaces for 
holes.

c.  Remove your shoes to avoid damaging the base or 

tearing the liner.

d.  Spread out the liner, smooth side down. Unfold the liner 

from the centre of the pool toward the sides. 

(Image 18)

e.  Smooth out all the wrinkles in the bottom. Do not leave 

any space between the liner and cove.

18

19

Important Note:

If possible, unfold the liner on the grass one to two hours 

before installation. Be careful not to leave the liner too long or 

you may damage the grass.

Important Note:

The liner is generally smaller than the support structure of 
the pool. It will stretch more easily when warm. It is important 
that the liner is installed on a warm sunny day. AVOID USING 
EXTRA COLD WATER AND INSTALLING ON A COLD DAY.

Содержание V35046






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды