manualshive.com logo in svg

Piscine Solide V35046, Руководство по установке

Поделиться
Скачать
Piscine Solide V35046 Скачать руководство пользователя страница 27

No Diving or Jumping.  Observe all Safety Rules

1-1

1. The Terrain

Pay special attention to choosing the right location for your 
pool:

• Choose a large area, as flat and level as possible and well 
drained. 

(Image 1)

• Choose a spot on dry, firm earth (stabilizer or other)—do 
not install the pool on asphalt, tar or oil based surfaces, 
gravel, peat moss, wood or chemically treated soil.

• Check with your pool dealer to see if Nut Grass grows in 
your area. This type of grass may grow up through your pool 
liner. Your dealer will be able to advise how best to treat the 
site.

• Sloped areas will need to be made level by digging away 
high spots, not by filling low spots—be prepared to hire 
earth-moving equipment if necessary. 

(Images 2a & 2b)

• Ensure the earth is well compacted and a wall is placed to 
prevent the earth from seeping out. 

(Image 2a)

• If you need to install partly in the ground, you must contact 
your dealer to see if this is an option for you and that you 
meet law requirements in your jurisdiction. 

(Image 2c)

1

Important Note:

Ground preparation is one of the most important steps in the 
installation process. A proper foundation will ensure the rest 
of the pool assembly goes smoothly and that no problems will 
occur when the pool is filled with water.

2a

2c

2b

GENERAL INSTRUCTIONS - ROUND POOLS

GROUND PREPARATION

Section

1

A. DETERMINE THE LOCATION OF YOUR POOL

READ ALL INSTRUCTIONS CAREFULLY

The approximate time it takes for installation, excluding earthworks and filling is 

about 1/2 day. You will need at least 3 people to help with installation.

Содержание V35046






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды