Pirate 121-0510-A-EDC Скачать руководство пользователя страница 6

Страница: 6 / 30

Manual Revision: June 20

C-Series Jr - 0.5 / 1.0

Cu Ft

User’s Manual

WARNING

: This section of the manual is designed to give you a general understanding of how the

Abrasive Blaster functions.

All

sections of this manual must be read and understood before

operating the equipment.

Flow of Compressed Air
Flow of Abrasive
Flow of Exhaust Air

During Blow-down

ADDING ABRASIVE

Abrasive is added through the hole in the top of the Abrasive Blaster where the Pop-up and its seat are

located. When abrasive is added, it flows down through the hole, around the Pop-up, and down to the

bottom of the pressure vessel where it will exit through the Metering Valve when blasting is started.

PRESSURIZATION

When a compressed air source (such as an air-compressor) is connected to the inlet of the Abrasive

Blaster and the Inlet Shut-Off Valve is opened, compressed air flows to the Inlet Valve where it is stopped.

When the control handle is activated, the Inlet Valve opens and air flows into the Pressure Vessel causing

the Pop-up (located internally) to seal against its seat. Simultaneously, the Diaphragm Valve closes

sealing the Pressure Vessel allowing it to hold pressure. Air will also continue past the Choke Valve,

through the Pusher Line, and finally to the “tee” under the Metering Valve where it is mixed with abrasive.

The mixture of compressed air and abrasive will now exit the Abrasive Blaster through a blast hose and

nozzle connected to the coupling under the Metering Valve and blasting begins. It is important to note

that, some abrasive will collect at the base of the Metering Valve causing the blast hose to pulsate and

spray abrasive erratically for a short time while pressure builds up in the pressure vessel. This is normal

and will not damage the Abrasive Blaster.

DEPRESSURIZATION (BLOW-DOWN)

When the control handle is released in a pressure release (CPR) system, the Inlet Valve automatically

closes stopping the flow of compressed air into the Pressure Vessel. Simultaneously, the Diaphragm

Valve opens allowing the compressed air in the pressure vessel to exit the Abrasive Blaster through the

Diaphragm Valve. When all the pressure in the Pressure Vessel is released, blasting stops.

How CPR Systems Work

(Pressure Release)

Содержание 121-0510-A-EDC






























Результаты поиска

Содержание 121-0510-A-EDC

Отзывы:

Pirate 121-0510-A-EDC, Руководство пользователя, Страница: 6 / 30

Результаты поиска

Содержание 121-0510-A-EDC

Отзывы: