5 minute guide
02
11
En
The configuration shown on-screen should reflect the
actual speakers you have.
1
If you see an error message (
ERR
) in the right side
column (or the speaker configuration displayed isn’t
correct), there may be a problem with the speaker
connection. If selecting
RETRY
doesn’t work, turn off the
power and check the speaker connections. If there
doesn’t seem to be a problem, you can simply use
/
to select the speaker and
/
to change the setting
(and number for surround back) and continue.
6
Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for Channel Level, Speaker
Distance, Standing Wave and Acoustic Cal EQ.
Again, try to be as quiet as possible while this is
happening. It may take 3 to 7 minutes.
7
The Auto MCACC Setup has finished! Press RETURN
to go back to the System Setup menu.
2
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC setup.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
System Setup menu (starting on page 39).
3
Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto
MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary. If there are any instructions
showing in the front panel display, please follow them.
• Some older TVs may interfere with the operation of
the microphone. If this seems to be happening,
switch off the TV when doing the Auto MCACC Setup.
Playing a source
Here are the basic instructions for playing a source (such
as a DVD disc) with your home theater system.
1
Switch on your system components and receiver.
Start by switching on the playback component (for
example a DVD player), your TV
4
and subwoofer (if you
have one), then the receiver (press
RECEIVER
).
• Make sure the setup mic is disconnected.
2
Select the input source you want to play.
You can use the input source buttons on the remote
control,
INPUT SELECT
, or the front panel controls.
5
3
Press AUTO/DIRECT (AUTO SURR/STREAM
DIRECT) to select ‘AUTO SURROUND’ and start
playback of the source.
6
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, you should hear surround sound. If you are
playing a stereo source, you will only hear sound from the
front left/right speakers in the default listening mode.
• See also
Listening to your system
on page 31 for
information on different ways of listening to sources.
It is possible to check on the display whether or not multi-
channel playback is being performed properly.
When using a surround back speaker,
2
D+PL IIx
MOVIE
is displayed when playing Dolby Digital signals,
and
DTS+Neo:6
is displayed when playing DTS 5.1-
channel signals.
When not using a surround back speaker,
DOLBY
DIGITAL
is displayed when playing Dolby Digital signals.
4
Use the volume control to adjust the volume level.
Turn down the volume of your TV so that all sound is
coming from the speakers connected to this receiver.
Note
1 If you’re using the front panel display, the diagram in
Listening to Surround Sound
on page 9 indicates (in bold) how each speaker is displayed.
2 You can also choose to view the settings from the MCACC Data Check screen. See
Automatic MCACC (Expert)
on page 39 for more on this.
3 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different size
settings. You can correct the setting manually using the
Manual speaker setup
on page 49.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and
room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend adjusting
the settings manually.
4 Make sure that the TV’s video input is set to this receiver (for example, if you connected this receiver to the
VIDEO 1
jacks on your TV, make sure that the
VIDEO 1
input is now selected).
5 If you need to manually switch the input signal type press
SIGNAL SEL
(page 34).
6 • You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS and
88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.
• Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a
multichannel listening mode (see
Listening in surround sound
on page 31 if you need to do this) if you want multichannel surround sound.
DVD
BD
TV
HDMI
DVR 1
DVR 2
CD
XM
SIRIUS
CD-R
DIMMER
FM/AM
1
2
3
SLEEP
MCACC
INPUT
SELECT
GENRE
iPod USB
RECEIVER
SOURCE
DVD
BD
TV
HDMI
DVR 1
DVR 2
CD
XM
SIRIUS
CD-R
FM/AM
1
2
INPUT
SELECT
iPod USB
RECEIVER
INPUT
MUTE
EXIT
TOOLS
AUDIO
PARAMETER
VOL
CH
TV CONTROL
4
5
6
A.ATT
SBch
SR+
7
8
9
CLASS
MASTER
VOLUME
CH LEVEL
D.ACCESS
0
ENTER
TUNE
VIDEO
PARAMETER
MASTER
VOLUME
RETURN
iPod CTRL
SETUP
CATEGORY
AUTO/
DIRECT
THX
STATUS
PHASE
HDD
STEREO/
A.L.C.
DVD
STANDARD
BD MENU
ADV SURR
ANT
AUDIO
DISPLAY
MPX
SIGNAL SEL
CH
TUNE
MEM
AUTO/
DIRECT
HDD
VSX-03TXH_KU.book 11 ページ ２００８年４月１６日 水曜日 午後１時１９分
