Pioneer VSX-330-K Скачать руководство пользователя

Страница: 33 / 36

Additional information

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the

factory default. Use the front panel controls to do this.

Switch the receiver into standby.

While holding down

BAND

, press and hold



STANDBY/ON

for about two seconds.

When you see RESET? appear in the display, press

AUTO SURROUND/STREAM DIRECT

OK?

shows in the display.

Press

ALC/STANDARD SURR

to confirm.

appears in the display to indicate that the receiver

has been reset to the factory default settings.

Important

•

If the ARC function is ON, you may not be able to initialize

the unit. If this happens, turn OFF the ARC function or turn

OFF all the connected device before turning OFF

(STANDBY) the power for this unit, and initialize after the

HDMI indicator goes out.

•

If the

Standby Through

is not set to

OFF

, you may not be

able to initialize the unit.

Cleaning the unit

•

Use a polishing cloth or dry cloth to wipe off dust and dirt.

•

When the surface is dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water,

and wrung out well, and then wipe again with a dry cloth.

Do not use furniture wax or cleansers.

•

Never use thinners, benzine, insecticide sprays or other

chemicals on or near this unit, since these will corrode the

surface.

Specifications

Audio section

Rated power output

Front, Center, Surround

. . . . . . . . . . . . . . . . . . 105 W per channel (1 kHz, 6



, 1 %)

. . . . . . . . . . . . . . . . . 100 W per channel (1 kHz, 6



, 0.7 %)

For Oceania model

Maximum power output (Front, Center, Surround)

. . . . . . . . . . . . . . . . . 120 W per channel (1 kHz, 6



, 10 %)

Total Harmonic Distortion

. . . . . . . . . . . . . . . . . . . 0.06 % (20 Hz to 20 kHz, 8



, 50 W/ch)

Frequency response (LINE Pure Direct mode)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Hz to 70 kHz dB

Guaranteed speaker impedance . . . . . . . . . . . . . . 6



to 16



Input (Sensitivity/Impedance)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 mV/47 k



Signal-to-Noise Ratio (IHF, short circuited, A network)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB

Video Section

Signal level

Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75



)

Tuner Section

Frequency Range (FM) . . . . . . . . . . . . . . 87.5 MHz to 108 MHz

Antenna Input (FM) . . . . . . . . . . . . . . . . . . . . 75



unbalanced

Frequency Range (AM) . . . . . . . . . . . . . . . 531 kHz to 1602 kHz

Antenna (AM). . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna

Digital In/Out Section

HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . . Type A (19-pin)

HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 55 mA

USB terminal . . . . . . . . USB2.0 Full Speed (Type A) 5 V, 0.5 A

Miscellaneous

Power Requirements. . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz

Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 W

In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.45 W

Dimensions . . . . . 435 mm (W) x 168 mm (H) x 326.5 mm (D)

Weight (without package). . . . . . . . . . . . . . . . . . . . . . . . . 7.3 kg

Furnished Parts

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Dry cell batteries (AAA size IEC R03) . . . . . . . . . . . . . . . . . . . 2

AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Quick start guide

Safety Brochure

Note

•

Specifications and the design are subject to possible

modifications without notice, due to improvements.

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic, and the double-D symbol are trademarks of Dolby

Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured

under license from DTS Licensing Limited. DTS, DTS-HD,

the Symbol, & DTS and the Symbol together are registered

Содержание VSX-330-K





































Результаты поиска

Содержание VSX-330-K

Отзывы:

Похожие инструкции для VSX-330-K

Бренды по названию

Популярные бренды

Pioneer VSX-330-K, Руководство по эксплуатации

Результаты поиска

Содержание VSX-330-K

Отзывы:

Похожие инструкции для VSX-330-K

Бренды по названию

Популярные бренды