Pioneer KFDH075UW Скачать руководство пользователя страница 34

Страница: 34 / 36

Trouble Shooting

Problem

Cause

Trouble Shooting/ Remedy

The power supply is turned OFF.

Turn the power supply ON.

The fuse in the PCB is gone or blown.

Replace fuse.

Running at low (model 75/100)

Switch to high mode

Reverse rotation (model 125/150)

Swtich the phase for power line

The set temperature is higher than room

temperature

Lower the set temperature.

The room temperature is excessively low for cooling

Can not operate as it is out of temperature

control range.

a Phase protector open (condensing unit)

refer to page 28

b High pressure switch open

Check if any
i. air blockage on outdoor unit.
ii outdoor fan motor malfunction
iii. refrigernat overcharge.
iv. outdoor ambient above operating limit.

Check if any
i. refrigerant gas leakage

c Low pressure switch open

d comp overload protector open

The unit is just started the cooling mode

Wait for a while

High infiltration through door, windows

Close the door ,windows

Low refrigerant level

check suction, discharge pressure and temperature

Air flow too high

Change fan speed

Drain pipe is cloagged, water overflow

Clear the drain pipe

Cooling , but not cold enough

Water discharge from

the unit

Unit cannot operate

In case of malfunction, perform the following preliminary check , before asking for repair service.

Air flow too small

At Cooling Mode, no

cold air is delivered

Check if any
i. refrigernat overcharge.

Содержание KFDH075UW





































Результаты поиска

Содержание KFDH075UW

Отзывы:

Бренды по названию

Популярные бренды

Pioneer KFDH075UW, Техническое руководство

Результаты поиска

Содержание KFDH075UW

Отзывы:

Бренды по названию

Популярные бренды