Pioneer Elite SC-55, Руководство по эксплуатации

Страница: 59 / 108

59
En
09
Using other functions
Setting What it does Option(s)
BRIGHT
(Brightness)
<d, e> Adjusts the overall brightness.
c
–6 to +6
d
Default: 0
CONTRAST
<d, e>
Adjusts the contrast between light and dark.
c
–6 to +6
d
Default: 0
HUE
<d, e>
Adjusts the red/green balance.
c
–6 to +6
d
Default: 0
CHROMA
(Chroma Level)
<d, e> Adjusts saturation from dull to bright.
c
–6 to +6
d
Default: 0
BLK SETUP
(Black Setup)
<f>
Sets the black level according to the video input signal.
Normally select
7.5
. If the dark parts of the picture are
all black with this setting, select
0
.
7.5
0
ASP
(Aspect)
<g>
Specifies the aspect ratio when input signals are output
at the HDMI output. Make your desired settings while
checking each setting on your display (if the image
doesn’t match your monitor type, cropping or black
bands appear).
THROUGH
NORMAL
a If the video picture deteriorates when this settings is switched ON , switch it OFF .
b ! When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some
cases no picture will be output due to copyright protection signals. In this case, change the setting.
! When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor)
connected by HDMI. When PURE is selected, the signals are output with the same resolution as when input
(see About the video converter on page 22 ).
!
If this is set to something other than AUTO , PURE and 480i/576i analog signals are input, 480p/576p signals
are output from the component output terminals.
c
!
This setting is valid for component outputs and HDMI output.
!
P.MOTION is disabled when PCINEMA is set to ON .
!
This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i sig-
nals).
d Adjustment is not possible unless V.ADJ (Advanced Video Adjust) is set to MEMORY .
e
!
This setting is only displayed when the video signals below are being input:
—
480i, 576i, 480p, 576p, 720p, 1080i analog video signals
—
480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals
f This adjustment is only possible when 480i signals are being input from the composite video jacks.
g
! If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the
monitor.
! This setting is only displayed when 480i/p or 576i/p video signals are being input.
Switching the speaker
terminals
If you selected 9.1ch FH/FW ,
7.1ch + Speaker B , 7.1ch FH/FW + ZONE 2 or
5.1ch + SP-B Bi-Amp
at Speaker system setting
on page 76 , you can switch between speakers
using the
SPEAKERS
button.
If you selected 7.1ch Front Bi-Amp ,
7.1ch + ZONE 2
,
5.1ch Bi-Amp + ZONE 2
,
5.1ch + ZONE 2+3 , 5.1ch F+Surr Bi-Amp
or 5.1ch F+C Bi-Amp , the button will simply
switch your main speaker terminals on or off.
% Use SPEAKERS on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
7.1ch Front Bi-Amp
,
7.1ch + ZONE 2
,
5.1ch Bi-Amp + ZONE 2 , 5.1ch + ZONE 2+3 ,
5.1ch F+Surr Bi-Amp
or
5.1ch F+C Bi-Amp
,
the button will simply switch your main speaker
terminal (A) on or off.
Press repeatedly to choose a speaker terminal
option:
When you select 9.1ch FH/FW , you can select
from:
!
SP: FH/FW ON – Front height or front wide
channels are added to the front, center,
surround and surround back channels
(maximum 7 channels) and a maximum of 9
channels are output. The front height and front
wide channels are switched automatically
according to the audio input signal.
!
SP: FH ON – Front height channels are added
to the front, center, surround and surround
back channels (maximum 7 channels) and a
maximum of 9 channels are output.
!
SP: FW ON – Front wide channels are added
to the front, center, surround and surround
back channels (maximum 7 channels) and a
maximum of 9 channels are output.
!
SP: OFF
– No sound is output from the
speakers.
When you select 7.1ch + Speaker B , you can
select from:
!
SP: A ON – Sound is output from the
A-speaker terminals (up to 9 channels
(including front height channels), depending
on the source).
!
SP: B ON – Sound is output from the two
speakers connected to the B-speaker
terminals. Multichannel sources will not be
heard.
!
SP: A+B ON – Sound is output from the
A-speaker terminals (up to 7 channels,
depending on the source), the two speakers
connected to the B-speaker terminals, and
the subwoofer. The sound from the B-speaker
terminals will be the same as the sound
from the A-speaker terminals (multichannel
sources will be downmixed to 2 channels).
! SP: OFF – No sound is output from the
speakers.
When you select 7.1ch FH/FW + ZONE 2 , you
can select from:
! SP: FH/FW ON – Front height or front wide
channels are added to the front, center and
surround channels (maximum 5 channels)
and a maximum of 7 channels are output.
The front height and front wide channels are
switched automatically according to the audio
input signal.
! SP: FH ON – Front height channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
! SP: FW ON – Front wide channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
!
SP: OFF – No sound is output from the
speakers.
When you select 5.1ch + SP-B Bi-Amp , you can
select from:
!
SP: A ON – Sound is output from the
A-speaker terminals (maximum 5 channels).