Pioneer AVH-X1650DVD, Руководство пользователя

Страница: 38 / 200

Black plate (38,1)
!
When this unit is connected to a power amp
with an LPF, turn this LPF off before perform-
ing auto EQ. Also set the cut-off frequency
for the built-in LPF of an active subwoofer to
the highest frequency.
!
The distance has been calculated by com-
puter to be the optimum delay to give accu-
rate results for the circumstances, so please
continue to use this value.
—
The reflected sound within the car is
strong and delays occur.
—
The LPF on active subwoofers or external
amps delay the lower sounds.
!
Auto EQ changes the audio settings as fol-
lows:
—
The fader/balance settings return to the
center position. (Refer to
Using fader/bal-
ance adjustment on page 29.)
—
The equalizer curve switches to Flat .
(Refer to Recalling equalizer curves on
page 29.)
—
The front, center and rear speakers will
automatically be adjusted to a high pass
filter setting.
!
Previous settings for auto EQ will be overwrit-
ten.
!
If using an AVH-X2650BT or AVH-X1650DVD,
connect a microphone extension cable (sold
separately) to the AUX input in advance.
Performing auto EQ
1 Stop the car in a place that is quiet, close
all the doors, windows and sun roof, and
then turn the engine off.
If the engine is left running, engine noise may
prevent correct auto EQ.
2 Fix the optional microphone in the center
of the headrest of the driver
’
s seat, facing
forward.
The auto EQ may differ depending on where you
place the microphone. If desired, place the mi-
crophone on the front passenger seat to carry
out auto EQ.
3 Turn the ignition switch to ON or ACC.
If the car
’
s air conditioner or heater is turned on,
turn it off. Noise from the fan in the air condi-
tioner or heater may prevent correct auto EQ.
4 Press the home button to switch to the
home display.
5 Touch the system key to open the system
menu.
6 Touch Auto EQ Measurement to enter
auto EQ measurement mode.
7 Plug the microphone into the micro-
phone input jack on this unit.
AVH-X5650BTand AVH-X4650DVD
AVH-X2650BTand AVH-X1650DVD
AUX input
(
AUX
)
Extension Cable
(sold separately)
Microphone
8 Touch Start to start auto EQ.
9 When the 10-second countdown starts,
get out of the car and close the door within
10 seconds.
A measurement tone (noise) is emitted from the
speakers, and auto EQ measurement begins.
When auto EQ is completed,
Please connect
the microphone for measurement. When fin-
ished, please push HOME key.
is displayed.
When the car
’
s interior acoustic characteristics
cannot be measured correctly, an error message
will be displayed. (Refer to
Understanding auto
EQ error messages on page 54.)
#
It takes about nine minutes for auto EQ measure-
ment to be completed when all the speakers are con-
nected.
#
To stop auto EQ, touch
Stop
.
10 Store the microphone carefully in the
glove compartment or another safe place.
If the microphone is subjected to direct sunlight
for an extended period, high temperatures may
cause distortion, color change or malfunction.
Selecting the video format
You can switch the video output format of V
OUT
between NTSC and PAL.
1 Press the home button to switch to the
home display.
2 Touch the system key to open the system
menu.
3 Touch Video Output Format on the sys-
tem menu to select the video output format.
NTSC
—
PAL
Note
You can switch the video output format only for
the source from this unit.
Setting the video signal
When you connect this unit to an AV equipment
to this unit, select the suitable video signal set-
ting.
!
As this function is initially set to Auto , the
unit will automatically adjust the video signal
setting.
!
You can operate this function only for the
video signal input into the AV input.
1 Press the home button to switch to the
home display.
2 Touch the system key to open the system
menu.
3 Touch Video Signal Setting on the system
menu.
Video Signal Setting
items are displayed.
!
AV
–
Adjusts the AV video signal
!
AUX
–
Adjusts the AUX video signal
!
Camera
–
Adjusts the rear view camera video
signal
!
TV
–
Adjusts the TV tuner signal
4 Touch
c
or
d
to select the desired video
signal appears.
Auto
—
PAL
—
NTSC
—
PAL-M
—
PAL-N
—
SECAM
System settings
38
Section
System settings
En
19
<CRD4760-A>38