background image

23

–   Where assessment is required in case of replacing or repairing the product, the manufacturer will appoint an assessor within 
10 working days to identify the alleged defect. The manufacturer will bear the repair costs by appointing a local tradesman. The 
manufacturer may choose to replace the product if the repair or the cost of repair is not feasible. The replacement product will 
be available for collection from the nearest reseller within 10 working days. The customer will bear the cost of assembly for the 
replacement product.

 

IMPORTANT

1. Manufacturer’s Disclosure 

This warranty against defects shall not apply in the following situations: 

A)  Where the product is not assembled in accordance with the instructions provided in the product kit. 
B)  Where the product is used to store corrosive materials such as fertilizer, chlorine etc;
C)  Where the damage to the product is caused by storms. 

2. Weatherproofing

This product is weatherproof to a certain level; however driving windy rain may cause the product to leak. Condensation may 
also occur in some weather conditions such as extreme heat or cold. The product should only be used for storing items such as 
gardening equipment and should not be used for articles that may be prone to damage if they come into contact with moisture.

We strongly recommend you use a waterproof sealant to fill any gaps or joins in order to minimise the risk of water entering.

3. Major Defects 

If the manufacturer is satisfied that the defect is a major defect, the purchase price may be refunded in lieu of providing a 
replacement product or repairing the product.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law or Consumer Guarantees 
Act 1993 (NZ). You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable 
quality and the failure does not amount to a major failure.

Содержание Skillion Series
























Отзывы: