manualshive.com logo in svg

Pierce Pumper, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Pierce Pumper Скачать руководство пользователя страница 23

© 2019 Pierce Manufacturing Inc. All Rights Reserved.

Pierce Pumper / 3-7

OPERATION

Pump Engagement and Disengagement

3-4.

Driveline Driven Pump

3-4.1

Pump Engagement

NOTE:

In manual override mode, the pump speed will be controlled only by the throttle pedal.

3-4.1a

Engaging Pump, Cummins or Detroit Engine with Allison Transmission

NEVER operate pump with Pump Shift Control in ROAD position.
Vehicle can move. Vehicle can override parking brake.
Moving vehicle can injure or kill.

If equipped with 4WD, engage the water pump with the transfer case in 2WD ONLY. Vehicle will move if 
the pump is engaged when in 4WD. Death or injury may occur.

Pump Engagement - Cummins or Detroit Engines

1. With the engine running at idle, shift transmission to NEUTRAL (N).

2. Apply parking brake.

NOTE:

If parking brake is OFF, safety interlocks prevent hand throttles or pressure governors from operating.

NOTE:

If parking brake is released during pump operation, the pump will disengage. Engine speed will fall to idle and water pressure 
will fall.

3. Chock the wheels.

NOTE:

Chock front and rear of tire every time vehicle is parked.

4. Apply the service brake by pressing and holding the brake pedal.

continued

PUMP ENGAGED LAMP

OK TO PUMP LAMP

ROAD POSITION (UP)

NEUTRAL POSITION (CENTER)

PUMP POSITION (DOWN)

Содержание Pumper



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды