PIE Evolution piecal 211 Скачать руководство пользователя страница 4

Page 4

EXIT MENU

 - exits this menu immediately and saves any 

changes. Menu will automatically exit after 30 seconds of 
inactivity.

AUTO OFF

 - If AUTO OFF is ON, the unit will turn off after 30 

minutes of inactivity to save battery life. If AUTO OFF is OFF the 
unit will stay on until the POWER SWITCH is moved to the off 
position.

BACKLIGHT

 - If BACKLIGHT is ON the backlight will light all the time the unit is powered up. For 

maximum battery life turn the backlight off when using the calibrator in areas with enough ambient 
light to read the display.

STEPS

 - pressing the knob will cycle through 2, 3, 5, 11 and 21 steps then reverse direction. The 

endpoints of the steps are based on the values stored in the 

HI

 and 

LO

 EZ-CHECK outputs. 

2 steps

 will automatically switch between the values stored in the HI & LO EZ-CHECK (0 & 

100%). 

3 steps

 between the HI, Midpoint and LO EZ-CHECK (0, 50 & 100%). 

5 steps

 between the HI and LO EZ-CHECK in 25% increments (0, 25, 50, 75 & 100%).

11 steps

 between the HI and LO EZ-CHECK in 10% increments (0, 10, 20...80, 90 &100%).

21 steps

 between the HI and LO EZ-CHECK in 5% increments (0, 5, 10... 90, 95 & 100%).

Note:

 All settings are remembered even with the power off. Removing the batteries resets the values 

to factory defaults.

STEP TIME

 - pressing the knob will cycle through 5, 6, 7, 8, 9, 10, 15, 20, 25, 30 and 60 seconds. 

To start the Automatic Stepping

Start automatic stepping by placing the EZ-CHECK Switch into the HI or LO position then press and 
hold the 

e

 DIAL KNOB for 6 seconds  (the word STORE will appear on the display after 3 seconds 

and continue to press the DIAL KNOB) until the word STEPPING appears on the display.  The word 
STEPPING will appear on the display anytime the selected automatic function is running. Stop the 
stepping by again pressing and holding the 

e

 DIAL KNOB for 3 seconds. 

FEATURES -  Auto Off,  Backlight & Automatic Stepping

FEATURES

> EXIT 

(2/2) 

 AUTO 

OFF  ON 

OFF

  

 BACKLIGHT 

  

ON 

OFF

STEPS 

3

STEP TIME         5

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

 TestEquipmentDepot.com 

Содержание Evolution piecal 211













Отзывы: