PI N-331 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 30

PI N-331 Скачать руководство пользователя страница 17

User Manual

PZ271E, valid for N-331

KSch, 1/18/2021

Physik Instrumente (PI) GmbH & Co. KG, Auf der Roemerstrasse 1, 76228 Karlsruhe, Germany

Page 17 / 30

Phone +49 721 4846-0, Fax +49 721 4846-1019, Email

[email protected]

−

N-331.1LU vacuum feedthrough (suitable for use in a vacuum to 10

-9

hPa), available

as optional accessory (p. 10)

−

N-331.02 air-side cable, available as optional accessory (p. 10)

−

Suitable tools for installing the vacuum feedthrough

Figure 12: Connection diagrams: Top: for N-331.xx at atmospheric pressure, bottom: for N-331.xxU at

vacuum to 10

-9

hPa

1.

For N-331.xxU: Install the vacuum feedthrough:

a)

Obtain the dimensions from the corresponding dimensional drawing (p. 27).

b)

Make sure that the vacuum feedthrough is oriented correctly, see p. 27.

c)

Make a suitable opening in the vacuum chamber.

d)

Install the vacuum feedthrough.

2.

Connect the drive and the electronics to each other as shown in the connection diagram

above.

3.

Take suitable measures to secure the connections against accidental disconnection.

«
...
15
16
17
18
19
...
»

Содержание N-331































Отзывы:

Нет отзывов