Phuel 108-3108-HV0 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 34

Phuel 108-3108-HV0 Скачать руководство пользователя страница 10

User Manual

Turnaround Sheave

108-3108-HV0
108-3108-HV1

OPS-3108 Rev E

9

3 Technical Description

The Phuel Turnaround Sheave provides the maximum tool string height in the
riser, while preserving the life of the wire by extending the wheel diameter to
20inches  –  making  it  suitable  for  the  larger  wire  diameters.  Magnets  have
been incorporated into the wheel so that the Phuel Detection system can be
used  to  confirm  that  the  wheel  is  turning  –  providing  extra  assurance  during
operations.

The  wheel  is  supported  on  two  ball  bearings  mounted  inside  a  housing  and
secured with a Seal Ring at one end, which is locked in place by a series of
inner  and  outer  plates.  The  plates  are  equally  spaced  around  the
circumference of the seal ring and secured with screws to prevent movement.

The Housing provides three lifting eyes so that the balance of the riser weight
can be accommodated while lifting. The outermost eyes are positioned so as
to provide an almost perfect balance point when the lubricators are attached
to make the handling and stabbing in process easier.

An  alternative  Bottom  Sub  can  be  provided  to  allow  the  Phuel  IRIS  tool
catcher to be directly incorporated without wasting more riser height and the
other  adapter  allows  the  Grease  head  to  be  directly  connected  without  the
need for any disassembly of its lower section.

At the top end there is a ½” NPT connection to facilitate the bleed off of gas if
it breaks out from the wire during operations. The lower grease injection ports
(½”  NPT)  are  used  to  prevent  the  well  debris  from  entering  the  bearings
during  operations.  A  grease  pump  must  be  connected  and  set  up  so  that
grease  is  constantly  being  pumped  through  at  a  rate  of  1  –  2  strokes  per
minute during operations irrespective of the operating pressures to maximise
the life of the bearings.

The  NPT  connects  are  cut  into  the  Phuel  saver  Sub,  which  is  a  removable
part  that  can  be  easily  replaced  if  damaged  without  the  need  to  repair  the
main housing. This port is a standard interface to many alternative Phuel parts
so  blank  ports,  check  valves,  valve  manifolds  or  isolating  valves  can  be
attached here to suit the required operation. Contact Phuel for more details if
required.

«
...
8
9
10
11
12
...
»

Содержание 108-3108-HV0



































Отзывы:

Нет отзывов