manualshive.com logo in svg

Photon Focus DR1-D3360-192-G2-8, Руководство пользователя, Страница: 58 / 119

Поделиться
Скачать
Photon Focus DR1-D3360-192-G2-8 Скачать руководство пользователя страница 58

5 Functionality

5.5

Bad Pixel Correction

The Bad Pixel Correction corrects single pixel defects of the image sensor. If a pixel is marked as
"bad" (defect) then its value is replaced by the mean of the two neighbouring pixels on the
same image row.

5.5.1

Enable / Disable the Bad Pixel Correction

The Bad Pixel Correction can be enabled or disabled with the property

ColCorrection_Enable

(in

category

Correction

/

ColCorrection

). By default the correction is enabled.

5.5.2

Calibration of the Bad Pixel Correction

The calibration of the Bad Pixel Correction is based on a grey reference image, which is taken
at uniform illumination to give an image with a mid grey level. The Bad Pixel Correction is
calibrated in the production of the camera. More defect pixels may appear due to normal
aging of the image sensor. It is possible to recalibrate the Bad Pixel Correction with the
following instructions:

1.

Setup the camera to the mode where it will be usually used. (Exposure time, ...). The
width and height should be set to its maximal value.

✎

If different exposure times will be used, calibrate the camera under the longest
exposure time.

2.

Put the camera in free-running mode by setting the property

TriggerMode

to

Off

.

3.

Start grabbing of the camera by clicking on the

Play

button.

4.

Wait until the camera has achieved working temperature.

5.

The image sensor must be uniformly illuminated to give an image with a mid grey level.
Check this before you proceed with the instructions.

6.

Set the visibility of the Device Control window of the PF_GEVPlayer to

Expert

.

7.

Every pixel that is above the higher threshold or below the lower threshold is marked as a
bad (defect) pixel. The values of these thresholds can be set by the properties

BadPixelCorrection_LowThreshold

and

BadPixelCorrection_HighThreshold

. These values must

match with acquired image used for calibration: only defect pixels should have a value
below

BadPixelCorrection_LowThreshold

or above

BadPixelCorrection_HighThreshold

. The

image could be saved to a file and viewed with an image viewer that has the ability to
show the histogram of the image as a list. A free tool with this feature is ImageJ. In the list
of histogram values check that there are only a few pixels above or below the thresholds.

8.

Run the command

BadPixelCorrection_Calculate

(category

BadPixelCorrection

) by clicking

on the corresponding button. The camera transmits a test image during calibration.

9.

The Bad Pixel Correction is now calibrated. The calibration values are stored in the
camera’s RAM and these values are lost when the camera power is turned off. To store the
calibration values to permanent memory see Section 5.5.3.

It is recommended to do the calibration without a lens. The quality of the grey
reference image is crucial for proper Bad Pixel Correction.

58

Содержание DR1-D3360-192-G2-8
























































































































Отзывы:

Нет отзывов