Photon Focus DR1-D3360-192-G2-8 Скачать руководство пользователя страница 100

Страница: 100 / 119

7 Software

7.7

Permanent Parameter Storage / Factory Reset

The property

UserSetSave

(in category

UserSetControl

) stores the current camera settings in the

non-volatile ﬂash memory. At power-up these values are loaded.

The property

UserSetSave

(in category

UserSetControl

) overwrites the current camera settings

with the settings that are stored in the ﬂash memory.

The command

CameraHeadFactoryReset

(in category

PhotonfocusMain

) restores the settings of the

camera head

The property

CameraHeadStoreDefaults

(in category

PhotonfocusMain

) stores only

the settings of the camera head in the ﬂash memory. It is recommended to use

UserSetSave

instead, as all properties are stored.

The calibration values of the FPN calibration are not stored with

UserSetSave

(or

CameraHeadStoreDefaults

). Use the command

Correction_SaveToFlash

for this (see

Correction_SaveToFlash

7.8

Persistent IP address

It is possible to set a persistent IP address:

Set

GevPersistentIPAddress

(in category

TransportLayerControl

) to the desired IP address.

Set

GevPersistentSubnetMask

(in category

TransportLayerControl

) to the sub net mask.

Set

GevCurrentIPConfigurationPersistent

(in category

TransportLayerControl

) to True.

Set

GevCurrentIPConfigurationDHCP

(in category

TransportLayerControl

) to False.

The selected persistent IP address will be applied after a reboot of the camera.

100

Содержание DR1-D3360-192-G2-8
























































































































Результаты поиска

Содержание DR1-D3360-192-G2-8

Отзывы:

Photon Focus DR1-D3360-192-G2-8, Руководство пользователя, Страница: 100 / 119

Результаты поиска

Содержание DR1-D3360-192-G2-8

Отзывы: